Crestron pmk-12l User Manual
Pre-Construction Mount Kit: PMK-12L
o Drive
l: 888.CREST
Rockleigh, NJ 07647
(2013441)
Te
RON
07.05
Fax: 201.767.7576
Specifications subject to
www.crestron.com
change without notice.
Description
Installation
The PMK-12L is a pre-construction mount kit for the
Crestron Isys
Crestron Isys
®
TPS-12L and TPS-12G-L wall mounted
touchpanels. The PMK-12L is used for installation on a
stud. For custom touchpanel placement without a stud,
use the WMKT-12L or the WMKM-12L. The PMK-12L
includes an 18 AWG bus wire to secure touchpanel
cabling prior to drywall installation and to avoid
damaging the cables when the opening is routed. Refer to
the physical views (bottom, side, and front) of the
PMK-12L, shown after this paragraph. The table that
follows lists all parts included with the PMK-12L.
stud. For custom touchpanel placement without a stud,
use the WMKT-12L or the WMKM-12L. The PMK-12L
includes an 18 AWG bus wire to secure touchpanel
cabling prior to drywall installation and to avoid
damaging the cables when the opening is routed. Refer to
the physical views (bottom, side, and front) of the
PMK-12L, shown after this paragraph. The table that
follows lists all parts included with the PMK-12L.
The PMK-12L consists of a single metal plate, which
fastens to the stud of a framed wall prior to hanging
drywall (shown after this paragraph). Standard drywall
nails or screws to attach the PMK-12L are not supplied
(length can vary).
fastens to the stud of a framed wall prior to hanging
drywall (shown after this paragraph). Standard drywall
nails or screws to attach the PMK-12L are not supplied
(length can vary).
Metal Plate Secured to Stud
.
Use inside edge for cutting drywall
NOTE: This mounting kit is to be used only with the
TPS-12L and TPS-12G-L series of touchpanels.
TPS-12L and TPS-12G-L series of touchpanels.
PMK-12L Physical Views
The plate is designed to provide the necessary support for
a single touchpanel and can mount to the right or left side
of a stud. Confirm that the PMK-12L is level before
application of drywall. A rectangular opening with the
dimensions shown in the illustration after this paragraph
must be made in the drywall. Verify that the opening
exposes the #6-32 tapped holes in each corner.
a single touchpanel and can mount to the right or left side
of a stud. Confirm that the PMK-12L is level before
application of drywall. A rectangular opening with the
dimensions shown in the illustration after this paragraph
must be made in the drywall. Verify that the opening
exposes the #6-32 tapped holes in each corner.
Dimensions for Drywall Cutout
If the opening for the touchpanel in the drywall is too
large, two pre-construction accessories are available to
make adjustments. Use the optional TMK-12L (Trim
Ring Kit) to provide a smooth edge at the opening. This
option provides a finished appearance and is preferred
when wallpaper is hung. Use the optional MMK-12L
(Mud Ring Kit) to fill in larger irregularities around the
opening (requires plastering).
large, two pre-construction accessories are available to
make adjustments. Use the optional TMK-12L (Trim
Ring Kit) to provide a smooth edge at the opening. This
option provides a finished appearance and is preferred
when wallpaper is hung. Use the optional MMK-12L
(Mud Ring Kit) to fill in larger irregularities around the
opening (requires plastering).
Supplied Components
DESCRIPTION
PART NUMBER QUANTITY
Metal, Plate, Mounting
2012962
1
Metal, Plate,Cover
2012966
1
Screw, #6-32, 1-1/2”L, Pan, Phil
2007254
8
Jumper wire, 12”L, 18AWG, Black
2007838
1
Complete the installation by either installing the
touchpanel, leaving the hole open (if permitted by local
building codes), or installing the supplied cover plate with
touchpanel, leaving the hole open (if permitted by local
building codes), or installing the supplied cover plate with
Crestron Electronics, Inc.
Installation Guide – DOC. 6358
15 Volv