Crestron clw-dim clw-dims clw-slvd User Manual

 

CLW-DIM, DIMS, & SLVD(W/A/B) 

Following are specifications for the -DIM, -DIMS, and  
-SLVD. 

The CLW-DIM (-DIM) is a stand-alone wall box dimmer 
that can also act as a Cresnet

®

 device that reports to a 

Crestron

®

 control processor. The CLW-DIM has four 

preset lighting levels that can be adjusted (refer to note 
below). The CLW-DIM also includes two isolated, non-
polarized Cresnet wires (plus a ground wire) for 
connecting to the Cresnet network over a twisted pair 
wire with shield.  

Power Requirements 

Line Power, 120 VAC, 60 Hz 

Default Net ID 

-DIM: 6D 
-DIMS: 6E 

Switch Type 

Dimmer 

Load Type 

Incandescent, Tungsten-Halogen, 
Magnetic Low Voltage 

2-Series Control System 
Update File

1,2

 

Version 3.093 or later 

Load Ratings

3

 

 

 Incandescent/Tungsten 

Halogen 

-DIM: 1000W 
-DIMS: 1000W 
-SLVD: N/A 

  Magnetic Low Voltage

4

 

-DIM: 1000VA/750W 
-DIMS: 1000VA/750W 
-SLVD: N/A 

Operating Temperature 
and Humidity 

32°F to 104°F (0°C to 40°C) 
10 to 90% Relative Humidity 

(Non-Condensing) 

Dimensions and Weight 

-DIM and -DIMS: 
  Height: 4.13 in (10.48 cm) 
  Width: 2.38 in (6.03 cm) 
  Depth: 1.91 in (4.85 cm) 
  Weight: 4.9 oz (0.67 kg) 
-SLVD: 
  Height: 4.13 in (10.48 cm) 
  Width: 1.75 in (4.45 cm) 
  Depth: 1.91 in (4.85 cm) 
  Weight: 3.6 oz (0.50 kg) 

NOTE:  The four preset levels are noted as Button 1-
High, Button 1-Low, Button Preset 2, and Button Preset 
3. Preset “Button 1-High” is usually used for turning 
lights on to full brightness while preset “Button 1-Low” is 
usually used for turning the lights off. Although “1-High” 
and “1-Low” are usually used for “On” and “Off” 
respectively, the light level for each preset can be 
customized by the user. Refer to “Operating Buttons and 
Switches” on page 5 for more information on customizing 
light levels. 

The CLW-DIM features a three-position mode selection 
switch. Refer to “Operating Buttons and Switches” on 
page 5 for more information. In the absence of Cresnet 
communications, the dimmer can still be used to control 
lighting. 

The CLW-DIMS (-DIMS) is similar to the -DIM with the 
added capability of working with a slave unit  
(CLW-SLVD) in a multi-switch / single circuit 
application. 

The CLW-SLVD (-SLVD) is a slave unit that when used 
in conjunction with the -DIMS acts as an additional 
dimmer control point in a multi-dimmer / single circuit 
application. It does not connect to a Cresnet system and 
cannot be used without a -DIMS. The -SLVD does not 
have a mode selection switch and is not programmable. It 
emulates the operation of the -DIMS to which it is 
connected. 

1. 

The latest software versions can be obtained from the Crestron 
website. Refer to the NOTE following these footnotes. 

2. 

Crestron 2-Series control systems include the AV2 and PRO2. 
Consult the latest Crestron Product Catalog for a complete list of 
2-Series control systems. 

3. 

Refer to Derating Charts for Multigang Installations on page 3. 

The -DIM, -DIMS, and -SLVD are available in white, 
almond, and black. White units are designated by part 
numbers ending in “W”. Almond units are designated by 
part numbers ending in “A”. Black units are designated by 
part numbers ending in “B”. Each dimmer can be covered 
with a decorative faceplate (not supplied). 

4. 

VA ratings are for input power to the transformer. If you do not 
know the input power requirement of the transformer, use the 
bulb’s wattage rating to determine proper rating. 

NOTE:  Crestron software and any files on the website 
are for Authorized Crestron dealers and Crestron 
Authorized Independent Programmers (CAIP) only. New 
users may be required to register to obtain access to 
certain areas of the site (including the FTP site). 

 

 

15 Volvo Drive   Rockleigh, NJ 07647

   

Tel: 888.CRESTRON

   

Fax: 201.767.7576

Specifications subject to 

www.crestron.com

change without notice.