Crestron clw-dim1 dims1 slvd1 User Manual
CLW-DIM1, DIMS1, & SLVD1(W/A/B)
Physical Description
Physical view of CLW-SLVD1 (clockwise from top; Top, Side,
and Front)
and Front)
The -DIM1 and -DIMS1 contain one large pushbutton, a
light emitting diode (LED) with software adjustable
brightness*, and a three-position slider-switch, shown
after this paragraph. Line voltage connections are made at
the rear of the dimmer. Three Class 2 low voltage wires,
located on the front of the dimmer, provide a Cresnet
connection to a control system. The wires can be routed to
the bottom of the unit for placement outside of the wall
box. The -SLVD1 is similar to the -DIM1 and -DIMS1
but does not have the slider-switch or the Class 2 low
voltage wires.
light emitting diode (LED) with software adjustable
brightness*, and a three-position slider-switch, shown
after this paragraph. Line voltage connections are made at
the rear of the dimmer. Three Class 2 low voltage wires,
located on the front of the dimmer, provide a Cresnet
connection to a control system. The wires can be routed to
the bottom of the unit for placement outside of the wall
box. The -SLVD1 is similar to the -DIM1 and -DIMS1
but does not have the slider-switch or the Class 2 low
voltage wires.
* LED brightness can only be adjusted through Crestron programming
software.
CLW-DIM1/-DIMS1 (L) and CLW-SLVD1 (R) shown in white
1.75 in
(4.45 cm)
3.81 in
(9.68 cm)
4.13 in
(10.48 cm)
3.28 in
(8.32 cm)
1.91 in
(4.85 cm)
2.70 in
(6.86 cm)
1.50 in
(3.81 cm)
The -DIM1, -DIMS1, and -SLVD1 mount in a standard
wallbox and are covered using a decorative faceplate (not
included).
wallbox and are covered using a decorative faceplate (not
included).
Industry Compliance
Physical view of CLW-DIM1/-DIMS1 (clockwise from top;
Top, Side, and Front)
Top, Side, and Front)
1.75 in
(4.45 cm)
2.38 in
(6.03 cm)
3.28 in
(8.32 cm)
3.81 in
(9.68 cm)
4.13 in
(10.48 cm)
1.91 in
(4.85 cm)
2.70 in
(6.86 cm)
1.50 in
(3.81 cm)
This product is Listed to applicable UL Standards and
requirements by Underwriters Laboratories Inc.
requirements by Underwriters Laboratories Inc.
E239011
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
CAUTION: Changes or modifications not expressly
approved by the manufacturer responsible for compliance
could void the user’s authority to operate the equipment.
approved by the manufacturer responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or
television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful
interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or
television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to
2
• Stand Alone Wall Box Dimmer : CLW-DIM1, DIMS1, & SLVD1
Installation Guide – DOC. 6250A