Oricom m5050 User Manual
ABOUT YOUR PHONE
M5050 User guide.doc Page 3 of 6
2
Setting up your phone
Basic steps to setup
1. Plug
the
mains power adapter of the charger into the wall mains supply.
2. Insert
the
two AAA batteries observing the correct polarity, into the battery compartment on the handset.
3. Slide
the
battery door firmly into place.
4.
Place the handset on the base unit or the charger and let the batteries charge for a full 14 hours before using.
Handset may get warm during initial charge. This is normal.(Ensure wall mains supply is switched ON)
Handset may get warm during initial charge. This is normal.(Ensure wall mains supply is switched ON)
5.
Register the handset to the base unit. (Refer to ‘Register Handsets’ section for details.)
3
About your phone
Your Oricom M5000 Handset
PHONE
button
button
Arrow LEFT /
RECALL
button
button
Arrow RIGHT
/ CALLER
DISPLAY
button
DISPLAY
button
MEMORY
button
button
DEL
MUTE /
DELETE
DELETE
button
Speaker
button
button
INTERCOM
button
button
Ringer ON /
OFF button
Keypad
LOCK/
UNLOCK
UNLOCK
VOLUME
button for
earpiece &
earpiece &
ringer
LAST NUMBER
redial
Note: Before you can use this handset. You need to:
1.
Charge the batteries (for 14 hours).
2.
Register the handset (to the Base unit).
ABOUT YOUR PHONE
M5050 User guide.doc Page 4 of 6
4
Registering Handsets
Register a handset
This handset is GAP compatible. You must go through the registration process with a base unit in order for it to
operate. Each handset can register to one base at a time only. The current base will be deregistered when a new
base is registered. If you register the handset with another manufacturer’s base unit, some features may not be
available.
(The following procedure may not apply if the base unit is from another manufacturer. Please refer to the instruction
manual of the base unit.)
Ensure no handset is resting on the base unit’s charging cradle:
1. Press & hold
operate. Each handset can register to one base at a time only. The current base will be deregistered when a new
base is registered. If you register the handset with another manufacturer’s base unit, some features may not be
available.
(The following procedure may not apply if the base unit is from another manufacturer. Please refer to the instruction
manual of the base unit.)
Ensure no handset is resting on the base unit’s charging cradle:
1. Press & hold
HANDSETLOCATOR
button on the BASE UNIT for 10s until the IN-USE light flashes (you have 3
minutes to register handset).
2. Key in a base unit number
2. Key in a base unit number
1, 2, 3 OR 4,
If you have one base unit key in 1.
3. Key in your handset’s PIN code default
0000
.
4. Handset now registered. You will hear a tone + display shows a handset number.
5
Making Calls
Make a handset call
1. Key number into telephone.
2. If necessary, press
2. If necessary, press
MUTE/DEL
to clear single digit or Press & Hold
MUTE/DEL
to clear all digits
3. Press
PHONE
button to dial.
4. if necessary, press
LAST NUMBER REDIAL
button.
Answer a call
When the handset rings:
1. Press
1. Press
PHONE
or
SPEAKERPHONE
button.
End a call
1. Press
PHONE
or
SPEAKERPHONE
button. The
symbol disappears from the display.
Note: OUT-OF- RANGE warning
You may be out-of-range with the BASE UNIT if you hear a warning tone or the sound becomes distorted.
You may be out-of-range with the BASE UNIT if you hear a warning tone or the sound becomes distorted.
Either
1.
1.
Move handset closer within 20 seconds until the tone stops. Otherwise, your call may be cut off.
2.
Reposition & reconnect BASE UNIT to a phone connection closer to where the handset will be used
(an extension lead(s) for power & telephone line may be useful where necessary).
Note: Call timer - The call timer shows the duration of your current call on display.
Note: Before you can use this handset. You need to:
1.
Charge the batteries (for 14 hours).
2.
Register the handset (to the Base unit).