Tefal turbo pro User Manual
2. Place the Steam Control (
G
)
on
.
The production of steam automatically adjusts
to the temperature selected.
to the temperature selected.
4
The supply of water is cut off automatically to avoid any drips from the
soleplate when the temperature of the iron is too low to produce steam.
soleplate when the temperature of the iron is too low to produce steam.
A
NTI
-
DRIP FUNCTION
1. Place the thermostat control
(
H
) to match the type of fabric
to be ironed.
The light comes on (
The light comes on (
I
). Wait
for the light to go off and come
on again before you start
ironing
on again before you start
ironing
Our advice
Start with the fabrics to be ironed on a low temperature (•) and finish with those
which respond best to higher temperatures (••• or MAX)
If you iron a fabric made of a blend of fibres: set the temperature for the most
delicate fibre.
which respond best to higher temperatures (••• or MAX)
If you iron a fabric made of a blend of fibres: set the temperature for the most
delicate fibre.
2
3
The electronic system cuts the power off and the auto-stop warning light
(
(
L
) flashes if the iron is left vertically on its heel for more than 8 minutes
or for more than 30 seconds if left horizontal.
To restart the iron, shake it gently until the warning light stops flashing.
NB. When the auto-stop safety switch operates, the thermostat light will
remain off.
To restart the iron, shake it gently until the warning light stops flashing.
NB. When the auto-stop safety switch operates, the thermostat light will
remain off.
A
UTO
-
STOP SAFETY FEATURE
(depending on the model)
8
Place the Steam control (
G
) on DRY
. You can start ironing when the
indicator light (
I
) comes on for the second time.
I
RONING WITHOUT STEAM
S
ETTING THE TEMPERATURE
AND THE STEAM LEVEL
Linen
Cotton
Wool
Silk
Cotton
Wool
Silk
(
Viscose)
Synthetics
(Acetate, Acrylic,
Polyamide,
Polyester)
(Acetate, Acrylic,
Polyamide,
Polyester)
Important
• Your iron will only produce steam when the thermostat control is in the steam zone.
When first switching on the iron wait for 5 minutes after the iron is switched on for
steam to be produced.
steam to be produced.
• If you lower the thermostat, wait until the light goes out and comes on again before
ironing.
!
T
O IRON LINEN OR COTTON WITH A HIGH
FLOW OF STEAM
(depending on the model)
7
1. Set the thermostat control to Linen or Cotton.
2. Press the “Jeans” (
2. Press the “Jeans” (
K
) trigger while ironing. This
increases the flow of steam.
3. Do not press the trigger for more than 30
seconds. Wait a minute before using it again.
Press repeatedly on the Spray button
to
dampen the fabric.
or
Use the Burst of Steam button
pressing two
or three times in quick succession to obtain a
more powerful burst of steam.
more powerful burst of steam.
Important
Never use the Burst of Steam button
on silk and
synthetics.
R
EMOVING THE STUBBORN CREASES
6
1. Hang the garment up and hold the fabric taut
2. Place the thermostat control (
2. Place the thermostat control (
H
) on MAX,
press repeatedly on the Burst of Steam
button
button
and move the iron from top to
bottom.
Important
Hold the iron a few centimetres from the garment to
avoid burning delicate fabrics.
avoid burning delicate fabrics.
V
ERTICAL STEAM
!
5
!
Turbo Pro UK 019449 20/07/01 15:44 Page 2