ICOM IC-706MKIIG User Manual
62
■ A
AT
T--1
18
80
0 iin
ntte
errn
na
all s
sw
wiittc
ch
h d
de
es
sc
crriip
pttiio
on
n
The optional AT-180 has 3 operating conditions for
HF band operation. Select a suitable condition
according to your antenna system.
HF band operation. Select a suitable condition
according to your antenna system.
➀
Remove the top cover of the AT-180.
➁
Set the tuner switches to the desired positions
according to the table below.
according to the table below.
• S
Sp
pe
ec
ciiffiic
ca
attiio
on
ns
s ffo
orr tth
he
e A
AT
T--1
18
80
0
• Frequency coverage : 1.9 – 54 MHz
• Input impedance
• Input impedance
: 50
Ω
• Maximum input
: 120 W
power
• Minimum tuning
: 8 W
power
• Matching impedance : 16.7–150
Ω
(HF band)
range
20 –125
Ω
(50 MHz band)
• Tuning accuracy
: Less than SWR 1.5:1
• Insertion loss
: Less than 1.0 dB
(after tuning)
• Power supply
: 13.8 V DC/1 A
(supplied from
requirements
the transceiver’s ACC socket)
• Dimensions
(mm/in)
: 167(W)
× 58.6(H)× 225(D)
6
9
⁄
16
(W)
× 2
5
⁄
17
(H)
× 8
7
⁄
8
(D)
• Weight
: 2.4 kg; 5 lb 4 oz
• Supplied accessories
: coaxial cable
(1 m)
,
ACC cable
(DIN 13 pins)
• A
AT
T--1
18
80
0 iin
ns
siid
de
e tto
op
p c
co
ov
ve
err
• C
Co
on
nn
ne
ec
ctto
orr iin
nffo
orrm
ma
attiio
on
n ffo
orr A
AC
CC
C((2
2)) s
so
oc
ck
ke
ett
S2
S1
D C
B A
ACC 2
1
2
3
4
7
6
5
P
PIIN
N N
NO
O..//
N
NA
AM
ME
E
D
DE
ES
SC
CR
RIIP
PT
TIIO
ON
N
➀
8 V
Regulated 8 V output.
(10 mA max.)
(10 mA max.)
➁
GND
Connects to ground.
➂
SEND
Input/output pin.
Goes to ground when transmitting (20 mA
max). When grounded, transmits.
Goes to ground when transmitting (20 mA
max). When grounded, transmits.
➃
BAND
Band voltage output.
(Varies with amateur band; 0 to 8.0 V).
(Varies with amateur band; 0 to 8.0 V).
➄
ALC
ALC output voltage (–4 to 0 V).
➅
NC
No connection.
➆
13.8V
13.8 V output when power is ON (1 A max).
S
SW
W P
Po
ossiittiio
on
n
O
Op
pe
erra
attiio
on
n
S1
A
(default)
The tuner operating condition is set by S2
described below.
described below.
B
THROUGH INHIBIT
The tuner tunes the antenna even when
the antenna has poor SWR (up to VSWR
3:1 after tuning). In this case, manual tun-
ing is necessary each time you change the
frequency although the tuner automatical-
ly starts tuning when the VSWR is higher
than 3:1. This setting is called “through
inhibit,” however, the tuner is set to
“through” if the VSWR is higher than 3:1
after tuning.
The tuner tunes the antenna even when
the antenna has poor SWR (up to VSWR
3:1 after tuning). In this case, manual tun-
ing is necessary each time you change the
frequency although the tuner automatical-
ly starts tuning when the VSWR is higher
than 3:1. This setting is called “through
inhibit,” however, the tuner is set to
“through” if the VSWR is higher than 3:1
after tuning.
S2
C
TUNER SENSITIVE CONDITION
The tuner tunes each time you transmit
(except SSB mode). Therefore, the lowest
SWR is obtained at any given time.
For SSB mode, the same condition as the
“D” position.
The tuner tunes each time you transmit
(except SSB mode). Therefore, the lowest
SWR is obtained at any given time.
For SSB mode, the same condition as the
“D” position.
D
(default)
NORMAL CONDITION
The tuner tunes when the SWR is higher
than 1.5:1. Therefore, the tuner activates
only when tuning is necessary.
The tuner tunes when the SWR is higher
than 1.5:1. Therefore, the tuner activates
only when tuning is necessary.
10
OPTIONAL INSTALLATIONS/SETTINGS
IC-706MKIIG.qxd 02.3.27 13:53 Page 62