Hitachi vtfx980eukn User Manual
20
SETTING THE CLOCK MANUALLY
Things to know before starting
• While you are setting the clock, the display
panel on the remote control handset will
prompt you through the procedure.
prompt you through the procedure.
• Always press “0” before a single-digit hour,
minute, day, month or year.
• If you press the wrong digit during clock
setting, press the CORRECT button repeatedly
until the incorrect digit flashes then enter the
correct digit.
until the incorrect digit flashes then enter the
correct digit.
• You have about one minute to complete each
step in the procedure. If you do not proceed to
the next step within this time, all entries are
erased and you must start again.
the next step within this time, all entries are
erased and you must start again.
• The clock must be set to the correct time before
programming the timer for unattended
recording or Instant Recording Timer (IRT).
recording or Instant Recording Timer (IRT).
Notes:
• If you wish to correct the time in the VCR
• If you wish to correct the time in the VCR
display after transmitting the information to the
VCR, follow the steps above correcting the
information and transmit it again.
VCR, follow the steps above correcting the
information and transmit it again.
• If the power is interrupted for more than 30
minutes, “– –:– –” will appear in the VCR
display. The time and date will need to be reset.
display. The time and date will need to be reset.
Controls
Remote Display
1
2
3
4
Be sure to check that “VCR1” or “VCR2” is
displayed.
This VCR is designed so it can be controlled when
either “VCR1” or “VCR2” is selected.
See “REMOTE” on page 60.
displayed.
This VCR is designed so it can be controlled when
either “VCR1” or “VCR2” is selected.
See “REMOTE” on page 60.
Press the CLOCK button.
Set the time and date.
For example, press 1 0 2 0 for 10:20, and then
1 2 0 5 0 1 for the 12th of May, 2001.
(0:00 for midnight, 12:00 for noon)
The day of week appears automatically.
1 2 0 5 0 1 for the 12th of May, 2001.
(0:00 for midnight, 12:00 for noon)
The day of week appears automatically.
After setting the date, press the CLOCK button.
The clock starts counting and the blinking
“TRANS” appears.
“TRANS” appears.
5
Press the TRANS button while aiming the remote
control handset at the receiver on the VCR.
The transferred time appears on the display of the
VCR.
“TRANS” now stop blinking in the display.
control handset at the receiver on the VCR.
The transferred time appears on the display of the
VCR.
“TRANS” now stop blinking in the display.
DAY
MONTH
VCR
TRANS
YEAR
SA
1
6
Press the CLOCK button.
The remote control handset and the VCR clock
have now been set up.
The remote control handset and the VCR clock
have now been set up.
DAY
MONTH
VCR
SA
1
COMMERCIAL ADVANCE
PROG
O LINK
RE
IR
VIDEO LINK
CA
VCR
DAY
MONTH
YEAR
1
▲
▲
▲
▲
DAY
MONTH
▲ ▲
▲▲
▲
▲
VCR
YEAR
SA
1
DAY
MONTH
VCR
TRANS
YEAR
SA
1
▲
▲
▲
▲
▲
▲
▲
▲
ENTER
TRANS
3
2
1
1
4
2
3
6
4
9
8
0
7
PROG
SP/LP
MENU
CLOCK
COUNT
DISP
CH1/2
FWD
REV
0000
VCR1/2/TV
CLOCK
CORRECT
PDC
DLY/WKL
AUX
CL
5
CLOCK
CORRECT
CORRECT
VCR1/2/TV
TRANS
~
0
9
EXTEND
VIDEO
PLUS
PLUS
A. DUB
V. DUB
VCR
DAY
MONTH
1