Intermatic fl100hps User Manual

2. Using provided twist on or other approved connectors, connect the fixture wires to the supply

wires as follows: (See Figure 3)

a. Identify supply voltage.

b. Open lens door and remove reflector.

c. Select appropriate fixture wire to match incoming voltage. All fixtures are shipped with

277V wire ready for connection. If supply voltage is lower, cap wire marked 277V with

appropriate twist on wire connector and strip fixture wire marked with matching voltage.

d. Confirm unused voltage fixture wires are appropriately capped within fixture body.

e. Feed the matching voltage fixture wire through the mounting arm.

f. Replace and secure reflector in the same orientation as shown in Figure 2.

g. Close and secure lens door to prevent damage while wiring fixture to mounting.

h. Connect the fixture wire matching the incoming voltage to the black (hot) supply wire.

i.  Connect the fixture wire marked COM to the white (neutral) supply wire.

j. Connect the bare copper (fixture ground) wire to the supply grounding wire.

3. Make sure that all wires and connections are inside the mounting wiring compartment and that the 

cover is properly sealed to keep moisture out. To weatherproof fixture, seal all holes in housing 

(mounting conduit, plugs, photocontrols, etc.) with silicone sealant.

4. Open door. Screw lamp into lampholder until finger-tight.

5. Close lens door, making sure that gasket is in place and compressed to seal out moisture.

6. To operate, restore power to the circuit and switch light on.

Do not turn mounting arm more than 360˚ after wires are connected. Excessive twisting of wires 

may loosen connections.

1. Turn off power at circuit breaker or fuse box. Rotate mounting arm until light is pointing in the 

desired direction. Tighten locknut to secure.

2. Loosen mounting arm bolt (do not remove) and tip fixture to desired angle. Retighten bolt to secure.

3. Turn power on and check aim. If adjustment is needed, turn power OFF at circuit breaker or fuse 

box and allow fixture to cool before adjusting.

1. Turn off power at circuit breaker or fuse box. Allow fixture and lamp to cool.

2. Release retaining clips and swing hinged fixture lens door open . Remove old lamp and replace

with new lamp of correct type and wattage. Screw lamp into socket in lampholder until finger-tight.

3. Close lens door and secure clips making sure that gasket is properly seated, free of debris, and 

compressed to seal out moisture.

4. Turn power back on.

5. Properly dispose of lamp per manufacturer’s recommendations.

If within one (1) year from the date of purchase, this product fails due to a defect in material or workmanship, Intermatic Incorporated will repair or replace it, at its sole option, free of charge. This warranty is extended

to the original purchaser only and is not transferable. This warranty does not apply to: (a) damage to units caused by accident, dropping or abuse in handling, acts of God or any negligent use; (b) units which have been

subject to unauthorized repair, opened, taken apart or otherwise modified; (c) units not used in accordance with instructions; (d) damages exceeding the cost of the product; (e) sealed lamps and/or lamp bulbs; (f) the

finish on any portion of the product, such as surface and/or weathering, as this is considered normal wear and tear; (g) transit damage, initial installation costs, removal costs, or reinstallation costs.

INTERMATIC INCORPORATED WILL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUEN-

TIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS OR IMPLIED WARRANTIES. ALL IMPLIED WARRANTIES,

INCLUDING THE WARRANTY OF MERCHANTABILITY AND THE WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY MODIFIED TO EXIST ONLY AS CONTAINED IN THIS LIMITED 

WARRANTY, AND SHALL BE OF THE SAME DURATION AS THE WARRANTY PERIOD STATED ABOVE. SOME STATES DO NOT ALLOW LIMITATIONS ON THE DURATION OF AN IMPLIED WARRANTY, SO THE

ABOVE LIMITATION MAY NOT APPLY TO YOU.

This warranty service is available by either (a) returning the product to the dealer from whom the unit was purchased, or (b) mailing the product, along with proof of purchase, postage prepaid to the authorized service

center listed below. This warranty is made by: Intermatic Incorporated/After Sales Service/7777 Winn Rd., Spring Grove, Illinois 60081-9698/815-675-7000  http://www.intermatic.com  Please be sure to wrap the 

product securely to avoid shipping damage.

THESE INSTRUCTIONS DO NOT COVER ALL VARIATIONS IN EQUIPMENT, NOR DO THEY PROVIDE FOR ALL SITUATIONS 

RELATED TO FIXTURE INSTALLATION, OPERATION OR MAINTENANCE. FOR FURTHER INFORMATION CONTACT YOUR 

DISTRIBUTOR OR INTERMATIC INCORPORATED - SPRING GROVE, ILLINOIS 60081 (815) 675-7000   www.intermatic.com

158HL12116

Figure 3