Crestron caen-ck-2x1 4x1 4x2 User Manual
CAEN-CK-2x1, 4x1, 4x2
Functional Summary
Installation
The cover extension kit should be attached to a Crestron
®
Automation Enclosure in accordance with all national and
local electrical codes. The enclosure cover and screws
must be removed prior to installation. Both must be
retained and used with the supplied screws to complete
the following procedure.
local electrical codes. The enclosure cover and screws
must be removed prior to installation. Both must be
retained and used with the supplied screws to complete
the following procedure.
The CAEN-CK-2x1/4x1/4x2 CAEN Cover Extension
Kits are designed to increase the overall depth of the
CAEN-2x1, CAEN-4x1, and CAEN-4x2 automation
enclosures by 1.5 inches. Adding depth to these
enclosures allows the enclosure to accommodate excess
wiring and third-party devices that may not normally fit in
the standard enclosure.
Kits are designed to increase the overall depth of the
CAEN-2x1, CAEN-4x1, and CAEN-4x2 automation
enclosures by 1.5 inches. Adding depth to these
enclosures allows the enclosure to accommodate excess
wiring and third-party devices that may not normally fit in
the standard enclosure.
Refer to the following procedure shown in the installation
diagram when installing the CAEN Cover Extension Kit.
diagram when installing the CAEN Cover Extension Kit.
CAEN-CK Overall Dimensions (Front and Side Views)
W
H
D
HORIZONTAL
PAN (x2)
VERTICAL
BRACKET (x2)
Installation Diagram
1. As shown in the installation diagram, place a
horizontal pan on the bottom and top of the CAEN
enclosure (edges facing inward). Use a #2 Phillips
tip screwdriver to secure the horizontal pans to the
enclosure using the 8-32 screws.
enclosure (edges facing inward). Use a #2 Phillips
tip screwdriver to secure the horizontal pans to the
enclosure using the 8-32 screws.
2. As shown in the installation diagram, place a vertical
bracket on the left and right side of the CAEN
enclosure (edges facing outward). Use a #2 Phillips
tip screwdriver and the 8-32 screws to loosely attach
the vertical brackets to the enclosure.
enclosure (edges facing outward). Use a #2 Phillips
tip screwdriver and the 8-32 screws to loosely attach
the vertical brackets to the enclosure.
The following table lists the dimensions (assembled) for
the CAEN-CK-2x1, CAEN-CK-4x1, and CAEN-CK-4x2.
the CAEN-CK-2x1, CAEN-CK-4x1, and CAEN-CK-4x2.
Dimensions of Enclosure Cover Kits
3. Secure the vertical brackets to the secured horizontal
pans with a #2 Phillips tip screwdriver and the 8-32
screws. Tighten the screws holding the vertical
brackets to the CAEN enclosure.
screws. Tighten the screws holding the vertical
brackets to the CAEN enclosure.
DIMENSION CAEN-
CK-2x1
CAEN-
CK-4x1
CAEN-
CK-4x2
H
23.50 in
38.90 in
38.90 in
D
1.50 in
1.50 in
1.50 in
W
15.35 in
15.35 in
26.50 in
4. After installing the required devices, use the
remaining screws to install the CAEN cover.
Crestron Electronics, Inc.
Installation Guide – DOC. 6336
15 Volvo Drive Rockleigh, NJ 07647
12.04
Tel: 888.CRESTRON
Fax: 201.767.7576
Specifications subject to
www.crestron.com
change without notice.