Intermatic wp1000hc User Manual
To install your receptacle cover, follow the
steps listed. (See figures 4, 5, 6, 7 and 8).
steps listed. (See figures 4, 5, 6, 7 and 8).
IF USING A POWER SCREWDRIVER, BE
CAREFUL NOT TO OVER TIGHTEN THE
SCREWS BECAUSE YOU WILL STRIP
THE THREADS IN THE JUNCTION BOX
AND/OR THE ELECTRICAL DEVICE.
CAREFUL NOT TO OVER TIGHTEN THE
SCREWS BECAUSE YOU WILL STRIP
THE THREADS IN THE JUNCTION BOX
AND/OR THE ELECTRICAL DEVICE.
1. If installation is being done on an existing
receptacle, remove the existing receptacle
cover and discard.
cover and discard.
2. The mounting screws which hold the
receptacle or GFI to the junction box can
be removed. Do not remove receptacle
wiring connections.
be removed. Do not remove receptacle
wiring connections.
3. Select the proper insert and press insert
into base/cover assembly. Press insert
firmly into this assembly and it will remain
there during the remaining assembly
steps.
firmly into this assembly and it will remain
there during the remaining assembly
steps.
4. Locate gasket as required for the installa-
tion. Be sure gasket is held to the back of
the base/cover and insert assembly using
the four projections molded on the insert
to locate the gasket.
the base/cover and insert assembly using
the four projections molded on the insert
to locate the gasket.
5. Mount the cover/base and insert assem-
bly, hinge on top, and the existing recepta-
cle to the junction box using two of the
long screws provided (DO NOT OVER
TIGHTEN).
cle to the junction box using two of the
long screws provided (DO NOT OVER
TIGHTEN).
CAUTION: DISCONNECT POWER TO THE
RECEPTACLE AT THE CIRCUIT BREAKER
PANEL BEFORE INSTALLING THIS RECEP-
TACLE COVER.
RECEPTACLE AT THE CIRCUIT BREAKER
PANEL BEFORE INSTALLING THIS RECEP-
TACLE COVER.
6. If mounting to an outdoor junction box or
field service (FS) box, use the remaining
long screws, two or four screws as
required, to further secure the cover/base
and insert assembly to the box. Note that
holes are located in the insert for mount-
ing to an FS box or any standard single
gang junction box. For specially designed
junction boxes, holes should be carefully
drilled to line up with the holes in the junc-
tion box to accommodate mounting.
long screws, two or four screws as
required, to further secure the cover/base
and insert assembly to the box. Note that
holes are located in the insert for mount-
ing to an FS box or any standard single
gang junction box. For specially designed
junction boxes, holes should be carefully
drilled to line up with the holes in the junc-
tion box to accommodate mounting.
7. Be sure all screws are secure but not over
tightened. Then install the remaining one
or two short screws into the receptacle as
required.
or two short screws into the receptacle as
required.
8. A molded tab (see Figure 8) is provided to
allow for padlocking the cover closed if
desired (Figure 9).
desired (Figure 9).
FOR BEST PROTECTION FROM RAIN
OR HUMIDITY, BE SURE TO ROUTE
THE CORDS THROUGH THE CORD
OUTLETS IN THE COVER AND PRESS
THE COVER FIRMLY UNTIL IT SNAPS
CLOSED.
OR HUMIDITY, BE SURE TO ROUTE
THE CORDS THROUGH THE CORD
OUTLETS IN THE COVER AND PRESS
THE COVER FIRMLY UNTIL IT SNAPS
CLOSED.
FULL ONE YEAR WARRANTY.
If within one (1) year from date of purchase this product fails due
to a defect in material or workmanship, Intermatic Inc. will repair
or replace it free of charge.
to a defect in material or workmanship, Intermatic Inc. will repair
or replace it free of charge.
This warranty does not apply to: a) damage caused by accident,
units struck by lightning, abuse, mishandling, dropping; b) units
which have been subject to unauthorized repair, opened, taken
apart; c) units not used in accordance with directions, d) dam-
ages exceeding the cost of the product. Some states do not allow
a limitation of damages so the foregoing limitation may not apply
to you. This warranty gives you specific legal rights and you may
also have other rights which may vary from state to state.
units struck by lightning, abuse, mishandling, dropping; b) units
which have been subject to unauthorized repair, opened, taken
apart; c) units not used in accordance with directions, d) dam-
ages exceeding the cost of the product. Some states do not allow
a limitation of damages so the foregoing limitation may not apply
to you. This warranty gives you specific legal rights and you may
also have other rights which may vary from state to state.
This warranty service is available by a) returning the product to
the dealer from whom it was purchased or b) mailing postage
prepaid to the address listed below. Please be sure to wrap the
product securely when mailing to avoid shipping damage.
the dealer from whom it was purchased or b) mailing postage
prepaid to the address listed below. Please be sure to wrap the
product securely when mailing to avoid shipping damage.
Intermatic Incorporated, 4720 West Montrose Avenue,
Chicago, Illinois 60641.
FIG. 4
FIG. 7
FIG. 8
FIG. 6
FIG. 5
PRINTED IN THE U.S.A.
158WP8450
Intermatic Incorporated
spring grove, illinois 60081-9698
CORD
OUTLETS
OUTLETS
LOCKABLE
TAB
TAB
FIG. 9
®