Crestron clti-2dim8 clxi-2dim8 User Manual
Crestron CLTI- & CLXI-2DIM8
Terminal Block & Module
Module Installation
NOTE: Before the bypass jumpers are removed, the
Crestron Professional Automation Computer (PAC2),
which provides control to the system, should be
properly connected and contain a valid program to
provide control of the module.
Crestron Professional Automation Computer (PAC2),
which provides control to the system, should be
properly connected and contain a valid program to
provide control of the module.
CAUTION: Module contains electrostatic sensitive
devices (ESDs); unit must be handled from metal
chassis – do not touch PC board or components.
devices (ESDs); unit must be handled from metal
chassis – do not touch PC board or components.
NOTE: Modules are to be installed after enclosure
has been completely wired. Refer to the terminal
block installation procedure on page 2 for details.
has been completely wired. Refer to the terminal
block installation procedure on page 2 for details.
Wiring Diagram of the Terminal Block to the Module
(Single-wide and Left Side Double-wide Enclosures)
(Single-wide and Left Side Double-wide Enclosures)
ENLARGEMENT DETAIL:
BYPASS JUMPERS ON
RED AND BROWN
SECTIONS HAVE BEEN
REMOVED AFTER
LOOSENING ALL
SCREWS.
BYPASS JUMPERS ON
RED AND BROWN
SECTIONS HAVE BEEN
REMOVED AFTER
LOOSENING ALL
SCREWS.
JUMPERS ON BLUE
SECTIONS ARE NOT
SECTIONS ARE NOT
REMOVED.
JUMPERS INSTALLED
BYPASS
JUMPERS
REMOVED
BLUE
TO LOADS
BROWN FROM BREAKER
RED
TO LOADS
RED
TO LOADS
BROWN FROM BREAKER
BLUE FROM BREAKER PANEL
BLUE
TO LOADS
BLUE FROM BREAKER PANEL
1. Use the four supplied self-tapping pan Phillips
screws (8B x ¼-inch (6 mm) length) to secure
the module to the enclosure.
the module to the enclosure.
2. As shown in the wiring diagrams (next column),
connect the wires from the module to the
terminal block. Each wire exits the module
directly in line with, and is the same color as, the
terminal to which it should be connected. Wires
are pre-stripped to 12 mm. Tighten to 1 Nm. Do
not over tighten.
terminal block. Each wire exits the module
directly in line with, and is the same color as, the
terminal to which it should be connected. Wires
are pre-stripped to 12 mm. Tighten to 1 Nm. Do
not over tighten.
3. If the module is being installed above another
module within the enclosure, attach the supplied
module interconnect cable between the two
modules. The illustration below depicts the area
within a double-wide enclosure where the
corners of four modules meet.
module interconnect cable between the two
modules. The illustration below depicts the area
within a double-wide enclosure where the
corners of four modules meet.
NOTE: One wire on the module interconnect cable
may be a different color from the rest. The color has
no bearing on its orientation during installation.
may be a different color from the rest. The color has
no bearing on its orientation during installation.
Wiring Diagram of the Terminal Block to the Module
(Right Side Double-wide Enclosures)
(Right Side Double-wide Enclosures)
Use Module Interconnect Cable to Wire Module to Module
MODULE
INTERCONNECT
CABLE ATTACHED
CONNECTION
NOT
MADE
BLUE FROM BREAKER PANEL
BROWN FROM BREAKER
BLUE
TO LOADS
BLUE FROM BREAKER PANEL
RED
TO LOADS
BROWN FROM BREAKER
RED
TO LOADS
BLUE
TO LOADS
BYPASS
JUMPERS
REMOVED
ENLARGEMENT DETAIL:
BYPASS JUMPERS ON RED
BYPASS JUMPERS ON RED
AND BROWN SECTIONS
HAVE BEEN REMOVED
AFTER LOOSENING ALL
SCREWS.
JUMPERS ON BLUE
SECTIONS ARE NOT
SECTIONS ARE NOT
REMOVED.
JUMPERS
INSTALLED
4. Turn on the circuit breaker and verify that the
green PWR LED on the module lights, the
breaker does not trip, and power is delivered to
the loads.
breaker does not trip, and power is delivered to
the loads.
5. Turn off the circuit breaker and remove the
bypass jumpers on the brown and red sections of
the terminal block. The jumpers on the blue
sections of the terminal block must remain
installed. Refer to the figures in the next column
for a close-up of the jumpers.
the terminal block. The jumpers on the blue
sections of the terminal block must remain
installed. Refer to the figures in the next column
for a close-up of the jumpers.
Installation Guide – DOC. 6411
Terminal Block & Module: CLTI- & CLXI-2DIM8
• 3