DKS Enterprises 1803PC User Manual
3.2 PROGRAMMING WITH A PC
Prior to programming the PC Programmable Telephone Entry System with the DoorKing Remote
Account Manager for Windows software and the user supplied PC, the system must have the
MASTER CODE programmed into it, and must be programmed to operate in the SINGLE or
MULTIPLE system format. These programming functions cannot be set with the PC and must be
programmed from the system keypad.
This telephone entry system has a programming function that is used in special circumstances when
interfaced with a DoorKing 1816 Telephone Intercom System. This CALL UP feature provides
special programming that will allow the system to call the phone number of a CO line connected to
the 1816 system. Once the 1816 answers the call, the system will automatically send out DTMF
tones that will activate the CALL UP feature in the 1816 system, and then send the four digit directory
code to the resident selected by the visitor. This allows visitors to contact tenants in the building that
do not have CO phone service through the telephone entry system. This feature IS NOT
programmable from the software and must be turned ON or OFF at the system keypad (3.2.3).
Account Manager for Windows software and the user supplied PC, the system must have the
MASTER CODE programmed into it, and must be programmed to operate in the SINGLE or
MULTIPLE system format. These programming functions cannot be set with the PC and must be
programmed from the system keypad.
This telephone entry system has a programming function that is used in special circumstances when
interfaced with a DoorKing 1816 Telephone Intercom System. This CALL UP feature provides
special programming that will allow the system to call the phone number of a CO line connected to
the 1816 system. Once the 1816 answers the call, the system will automatically send out DTMF
tones that will activate the CALL UP feature in the 1816 system, and then send the four digit directory
code to the resident selected by the visitor. This allows visitors to contact tenants in the building that
do not have CO phone service through the telephone entry system. This feature IS NOT
programmable from the software and must be turned ON or OFF at the system keypad (3.2.3).
3.2.1 Master Code
This programming step sets the system MASTER CODE. The master code is the four-digit number
required to gain access to the system memory. You need to know the master code prior to
programming the system with the PC, or to perform any of the programming functions on the
following pages.
NOTE: The master code cannot be programmed from an off-site location. The master code
can only be programmed from the system keypad.
Factory setting = 9999
required to gain access to the system memory. You need to know the master code prior to
programming the system with the PC, or to perform any of the programming functions on the
following pages.
NOTE: The master code cannot be programmed from an off-site location. The master code
can only be programmed from the system keypad.
Factory setting = 9999
1. Open the cabinet of the telephone entry system and turn the master code switch (the
small toggle switch) on.
2. Enter a four-digit master code _ _ _ _ then press * (beep).
3. Turn the master code switch off and close the cabinet.
3. Turn the master code switch off and close the cabinet.
3.2.2 Single or Multiple Systems
This program sequence sets the telephone entry system to operate as a single unit on the phone line,
or to share the phone line with other units. If multiple systems are sharing the same phone line, then
each one must be set as a "multiple system" and each must have a unique master code.
Factory setting = Single System.
or to share the phone line with other units. If multiple systems are sharing the same phone line, then
each one must be set as a "multiple system" and each must have a unique master code.
Factory setting = Single System.
1. Press *04 and then enter the four-digit MASTER CODE _ _ _ _ (beep).
2. Enter 0* (beep) for a single system or 1* (beep) for multiple systems.
3. Press 0# TOGETHER to end this programming step (beeeeeep).
2. Enter 0* (beep) for a single system or 1* (beep) for multiple systems.
3. Press 0# TOGETHER to end this programming step (beeeeeep).
32