INSTEON 2476s -15 User Manual

 

 
 

 

 

 

 

 

                                                                                 

                       

                  

     

Page 1 of 1 
Rev. 03-23-2012 

 

 

                                                                                        

                              

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

SwitchLinc

TM

 Relay – INSTEON

®

 Remote Control On/Off Switch 

(Non-Dimming), 3-Wire 

Remotely control lights and other non-dimmable devices in your home at the 
touch of a button. Send commands to SwitchLinc from an INSTEON 
controller. Or, conveniently control other linked INSTEON devices through the 
SwitchLinc paddle.  

 

Tap the paddle top to turn your light on. 

 Tap the paddle bottom to turn your light off. 

Note: For multi-way circuit installation, refer to the Owner’s Manual. 

1)  At the circuit breaker or fuse panel, disable the circuit supplying 

power to the switch. 

2)  Remove the wallplate from the existing switch, then unscrew the 

switch and pull it out from the junction box. 

3)  Disconnect the wires from the switch you are replacing and ensure 

you have 1/2” of bare wire on the ends. 

4)  To correctly identify the Line, Load, Neutral and Ground wires, 

enable power to the switch from the circuit breaker or fuse panel, 
use a line voltage meter, then turn the breaker off again. See Figure 
1 to properly connect your wires to the INSTEON device. 
Note: Mechanical switches don’t utilize Neutral wires, but they are 
usually available in the back of the switch box. 

5)  Ensure that all wire connectors are firmly attached and that there is 

no exposed copper except for the Ground wire. 

6)  Orient SwitchLinc with the LED bar at the left, gently place it into the 

junction box and screw it into place. 

7)  Enable power to the switch from the circuit breaker or fuse panel. 
8)  Test that SwitchLinc is working properly by turning the light on and 

off. 

9)  Reinstall the wallplate. 

1) 

Set SwitchLinc to linking mode* by pressing and holding the Set 
button until it beeps (3 seconds). 

2) 

At the responder, set it to the state you wish to activate from 
SwitchLinc. 

3) 

Press and hold the responder’s Set button for 3 seconds. 

 

4) 

Confirm that linking was successful by tapping the paddle on 
SwitchLinc on and then off. 

 

1) 

Set your INSTEON Controller to linking mode*. (For most 
controllers, press and hold the Set button for 3 seconds or 
an On/Scene button for 10 seconds.) 

2) 

Press and hold the Set button on SwitchLinc until it double-
beeps (3 seconds). 

3) 

Confirm that linking was successful by tapping the button 
you just linked to on the controller. 

 

 

Owner’s Manual: 

http://wiki.smarthome.com/index.php?title=2476S_Manual

  

Call: INSTEON Support Line at 800-762-7845 

 

Phillips and flathead screwdriver 

 Wire 

cutter/stripper 

 Voltage tester to identify wires inside the junction box

Installation should be performed only by a qualified electrician or a 
homeowner who is familiar and comfortable with electrical circuitry. If you 
have any questions regarding installation, we suggest consulting an 
electrician. If you have any questions regarding setup, contact the INSTEON 
Support Line. 

Paddle top 

(on)

LED bar

Paddle bottom  

(off) 

Set button

Figure 1 

*Setup modes will automatically time out after 4 minutes 

 

Limited Warranty – INSTEON warrants to original consumer of this product for a period of 2 years from date of purchase, this product will be free from 
defects in material and workmanship and will perform in substantial conformity with its Owner's Manual. Warranty shall not apply to defects caused by 
misuse or neglect.   
Protected under U.S. and foreign patents (see www.insteon.com) © Copyright 2012  
INSTEON, 16542 Millikan Ave., Irvine, CA 92606, 800-762-7845