Holland hitch xa-71 series User Manual

1

XA-71-D

1

Fifth wheel top plate for 2˝ kingpin

1A

XA-71-O

1

Fifth wheel top plate for 3.5˝ kingpin

1B

XA-71-03706

1

Fifth wheel top plate - 2˝ kingpin for
FW2570-7103 series or
FW2570-7113 series only

1C

XA-03711

1

Fifth whl. top plate - 3.5˝ kingpin
for FW2570-7103 or
FW2570-7113 series only

2

XB-5

1

Cotter pin 1/4˝ x 2˝

3

XA-1016-C

1

Lock pin

4

XB-T-60

1

Cotter pin 1/4˝ x2.5˝

5

XA-FW-108-D

1

Lock pin

6

XA-FW-104-D

1

Lock set for 2˝ kingpin

6A

XA-FW-104-03 

1

Lock set for 3.5˝ kingpin

7

XA-FW-128

1

Spring

8

XB-16

1

Cotter pin 1/8” x 1”

9

XA-FW-78

1

Secondary lock release handle

10

XA-FW-137-2

1

Secondary lock arm

11

XB-1028-2

1

Spring

12

XB-2083

1

Hex hd. bolt 1/2” - 20 x 1.75”

13

XB-T-49

1

Plain washer

14

XB-T-69-A

1

Hex lock nut

15

XA-1005-FH

1

Release lever

16

XA-1117-H

1

Release handle

16A

XA-03715

1

Release handle

17

XA-1104

1

Plunger

18

XB-1007

1

Compression spring (red)

19

XB-04473

1

Jam nut 1” - 14

20

XB-09407

1

Socket head cap screw

21

XB-HNH-58-C

1

Lock nut  5/8” - 11

22

XD-3123-1

1

Adjusting wedge

23

XB-403

1

Compression spring

24

XB-02949

1

Nylon bushing

25

XB-0769

2

Lube fitting (90˚)

26

XB-H-38

2

Lube fitting

* 27

XB-1604-9

2

Bushing (prior to 5/82)

* 27A

XB-0012-1

2

Bushing (5/82 - 9/87)

* 27B

XB-0012-3

2

Bushing (after 9/87)

* 28

XA-2632

2

Pivot bolt (prior to 11/86)

* 28A

XE-02759

2

Pivot pin (after 11/86)

* 29

XB-T-9N-2

2

Nut (prior to 11/86) (not shown)

* 30

XB-T-60

2

Cotter pin (prior to 11/86)

* 31

XB-21-S-375-1750

2

Roll pin

* 32

XB-T-69-A

2

Hex lock nut

* 33

XB-08002

2

Socket button head cap screw

* 34

TF-0110

1

Kingpin gage

* 35

TF-TLN-5001

1

2˝ kingpin lock tester

* 35A

TF-TLN-1500

1

3.5˝ kingpin lock tester

36

XA-05768-1 1

Adjusting 

block

37

XB-10327

1

Lock washer, 1˝

* Not included in Rebuild Kits

Part numbers indicated
throughout the instructions
in bold numbers—for
instance “fifth wheel top
plate (1)”—refer back to 
this drawing.

.25

3/16 ± 1/16

tab on the swing lock and a step end on the lock
arm, follow the instructions below and refer to
FIGURE A, at right.

1.

Coat the lock pin hole in the secondary lock (10) with
Never-Seez

®

(supplied with kit). DO NOT use a 

substitute lubricant.

2.

Install the secondary lock release handle (9) into the 
casting. Install the secondary lock onto the handle. 
Install a cotter pin (8) in the handle and spread it. 
Drive the secondary lock pin (3) through the holes in the
casting and secondary lock, and secure with a cotter pin
(2). Install a grease fitting (25) in the lock pin so that the
fitting faces the side, and will be accessible from the left
side of the tractor.

3.

Move the secondary lock handle to the closed position.
Check the location of the end of the secondary lock in
relation to the swinging lock. It should be 3/16˝ (0.188˝)
±1/16˝ (0.06˝) from point A on the swinging lock (see
FIGURE B) when the secondary lock is resting against the
casting at point B.

4.

If the secondary lock is not in the current position, 
install a secondary lock adjustment block (36) as shown
in FIGURE B. Move the adjustment block until proper
adjustment is achieved, then weld the adjustment block
in position, as shown in FIGURE B. After welding, 
check the dimension and for proper operation of 
the secondary lock.

.25

3/16 ± 1/16

adjustment block, follow the instructions below 
and refer to FIGURE C, at right.

1.

Pre-install the secondary lock (10) in the closed position
in the casting. Complete Steps 1, 2, and 3 before installing
the spring, release handle, and the secondary lock pin.
Align the lock pin holes and rotate the secondary lock up
against the adjustment block. Check the location of the
end of the secondary lock in relation to the swinging lock.
It should be 3/16˝ (0.188˝) ±1/16˝ (0.06˝) from point A on
the swinging lock (see FIGURE D) when the secondary lock
is resting against the adjusting block at point B.

2.

If the dimension is less that 1/8˝ (0.125˝), mark the area
where the secondary lock made contact with the adjusting
block. Remove the secondary lock, then place a bead of
weld on the adjusting block, where the secondary lock
makes contact with the adjusting block, and grind
smooth. Do not weld on the secondary lock. 
After welding, re-check as in STEP 1, in this section.

3.

If the dimension is more that 1/4” (0.25”), mark the 
area where the secondary lock makes contact with the
adjusting block. Remove the secondary lock, then grind
on the adjusting block. CAUTION: A small amount of
grinding on the adjusting block results in a large 
movement of the secondary lock. After grinding, re-check,
as in STEP 1, in this section.

C.

After a final check of the dimension, coat the lock pin
hole in the secondary lock (10) with Never-Seez

®

(supplied with kit). DO NOT use a substitute lubricant.

D.

Install the secondary lock release handle (9) into the 
casting. Install the secondary lock (10) onto the handle.
Install a cotter pin (8) in the handle and spread it. 
Drive the secondary lock pin (3) through the holes in the
casting and the secondary lock, and secure with a cotter
pin (2). Install a grease fitting (25) in lock pin so that the
fitting faces the side and will be accessible from the left
side of the tractor.