dls r4 User Manual
FILTER/CROSSOVER INSTALLATIONS
Filter installation and connection of MS5 & MS6
Filter installation and connection of R1070
Filter installation and connection of R964
Head unit / amp.
+
-
+
-
2-way crossover
INPUT WOOFER TWEETER
+
-
+
-
+
-
+
-
Woofer
Tweeter
THE JUMPERS INSIDE THE FILTER:
JUMPER J1
Jumper J1 is used for lowering the x-over frequency to the
tweeter.
tweeter.
J1 position Low
: When the tweeter is mounted apart from
the bass element (for example on the dashboard), use this
position .
position .
J1 position Hi
: When both tweeter and bass elements are
mounted close together (for example in the door side), use
this position .
this position .
TWEETER LEVEL: JUMPER J2
Select tweeter level by moving the small jumper J2 inside
the filter box.
the filter box.
High level
Mid level
Low level
Tw
level
Hi
Mid
Low
J2
J1
Hi
Low
Tw
x-over
freq.
Connection and tweeter level select
R1070:
R1070:
Use the red, blue and black cables to connect
between the filter box and speaker terminal. Note the
speaker terminal colour marking.
Select tweeter level by moving the jumper inside the
filter box between high / low. Make your own tests for
best result.
between the filter box and speaker terminal. Note the
speaker terminal colour marking.
Select tweeter level by moving the jumper inside the
filter box between high / low. Make your own tests for
best result.
How to connect R964:
1. Normal mode.
In normal use (not Bi-wiring) connect the input from head unit or
amplifier to the woofer input.
amplifier to the woofer input.
Jumper J1 and J2 must be in position IN.
2. Bi-wiring mode.
Bi-wiring means that the signal is separated to the woofer and
the tweeter. For example, when using separate amplifiers for
woofer and tweeter. Both filter inputs are used.
the tweeter. For example, when using separate amplifiers for
woofer and tweeter. Both filter inputs are used.
Set jumper J1
and J2 in position OUT to separate the filters + and ground.
If you connect the speaker element with active crossover, using
the amplifiers internal filters, you don´t need the filter boxes.
Use 3,5 kHz as X-over point.
the amplifiers internal filters, you don´t need the filter boxes.
Use 3,5 kHz as X-over point.
Tweeter level: jumper J3 and J4
The tweeter level can be adjusted in three steps by moving the
small jumpers (J2 and J3) inside the filter box.
small jumpers (J2 and J3) inside the filter box.
High level:
J3: IN
J4: IN
Mid level:
J3: IN
J4: OUT
Low level:
J3: OUT
J4: OUT
INPUT WOOFER TW
+ -
+ -
+ -
coaxial
2-way crossover
Red +
Blue +
Black -
Car stereo / amp.
Black = - common
Blue = + to woofer
Red= + to tweeter
Blue = + to woofer
Red= + to tweeter
Red = +
Black = -
CONNECTION R964, normal mode:
Car stereo / amp.
coaxial
2-way crossover
INPUT
OUT
WOOFER TWEETER WOOFER TWEETER
+ - + - +
- + -
IN OUT
IN OUT
J2 J1
OUT IN
OUT IN
J3 J4
Tweeter
level
level
Bi-wiring
on-off
on-off
coaxial
2-way crossover
INPUT
OUT
WOOFER TWEETER WOOFER TWEETER
+
-
+
-
+
-
+
-
Amp. for woofer
CONNECTION R964, Bi-wiring mode:
IN OUT
IN OUT
J2 J1
OUT IN
OUT IN
J3 J4
Tweeter
level
level
Bi-wiring
on-off
on-off
Amp. for tweeter
Hi Low
Black/blue
Black
Silver
Silver/red