Becker traffic assist pro Operating Guide
24
General operations
Fitting the unit bracket
The unit bracket can be secured directly
to the inside of the windscreen or to the
dashboard.
to the inside of the windscreen or to the
dashboard.
On the windscreen
If the dashboard is too far away from
the driver, the unit bracket can be
fitted irectly to the windscreen using the
suction mechanism.
If the dashboard is too far away from
the driver, the unit bracket can be
fitted irectly to the windscreen using the
suction mechanism.
!
Remove the adapter plate if already
attached to the suction cup (4). Pull
the lever (3) upwards and remove the
adapter plate (4).
attached to the suction cup (4). Pull
the lever (3) upwards and remove the
adapter plate (4).
!
Unscrew the fastening screws (5) and
(6).
(6).
!
Find a suitable position.
!
Press the suction cup on the unit
holder (4) against the windshield.
holder (4) against the windshield.
!
Rotate the unit bracket so that the sup-
port plate is roughly in the direction of
viewing required.
port plate is roughly in the direction of
viewing required.
!
Press the lever (3) downwards.
The bracket will have stuck firmly to the
windscreen. It can now be set precisely.
To remove, actuate the lever (3) again.
windscreen. It can now be set precisely.
To remove, actuate the lever (3) again.
On the dashboard
An adapter plate is provided for moun-
ting on the dashboard. This is stuck on to
the dashboard. The mounting face may
only be slightly curved.
An adapter plate is provided for moun-
ting on the dashboard. This is stuck on to
the dashboard. The mounting face may
only be slightly curved.
!
Find a suitable position.
!
Unscrew the fastening screws (5) and
(6).
(6).
!
Remove the protective film from the
lower contact surface of the adapter
plate.
lower contact surface of the adapter
plate.
!
Press the adapter plate onto the
instrument panel.
instrument panel.
!
Press the suction cup on the unit
holder (4) into the upper contact
surface of the adapter.
holder (4) into the upper contact
surface of the adapter.
!
Turn the unit holder such that the
carrier plate is positioned roughly in
the desired viewing direction.
carrier plate is positioned roughly in
the desired viewing direction.
!
Press the lever (3) downwards.
The bracket will have stuck firmly to the
adapter. It can now be set precisely.
To remove, actuate the lever (3) again.
adapter. It can now be set precisely.
To remove, actuate the lever (3) again.
Note:
Fasten the unit holder such that your
field of vision is not impaired when the
Traffic Assist Pro is installed and ensu-
re that the unit is outside the deploy-
ment area of the airbag.
Ensure that the electrical connection
cable does not hamper you from acces-
sing the vehicle's controls.
Also ensure that there is enough space
to easily slide the Traffic Assist Pro
back out of the bracket.
Clean the mounting area on the wind-
screen or dashboard so that it is clean
and free of grease. Do not use smearing,
soapy cleaning agents, otherwise this
may affect how it sticks to the dash-
board.
field of vision is not impaired when the
Traffic Assist Pro is installed and ensu-
re that the unit is outside the deploy-
ment area of the airbag.
Ensure that the electrical connection
cable does not hamper you from acces-
sing the vehicle's controls.
Also ensure that there is enough space
to easily slide the Traffic Assist Pro
back out of the bracket.
Clean the mounting area on the wind-
screen or dashboard so that it is clean
and free of grease. Do not use smearing,
soapy cleaning agents, otherwise this
may affect how it sticks to the dash-
board.
Note:
If the adapter plate is removed, you may
find residue from the glue on your dash-
board.
find residue from the glue on your dash-
board.