Panasonic MCCL485K Operating Guide

• 

The plug must be removed from the socket outlet before cleaning or maintaining the appliance. 

• 

To avoid injury, keep your fingers and hands away from the beater bar. 

• 

DO NOT use hot air or hot surface to dry filter. Keep at room temperature for approximately 24 hours. 

• 

IMPORTANT : Before re-installing the washable filter, make sure they are completely dry to avoid damaging the cleaner.

IMPORTANT:
Empty the dust compartment when it is full or the suction power seems 
to be bad.

NOTE: 
When vacuuming fine dust, such as powder or similar, there may be a 
loss of suction power. If this happens, empty the dust compartment and 
check for possible dust trapped on the filters.

D - 1  Push the dust compartment buckle and pull up the dust  
 

 

compartment from the main body.

D - 2  Rotate the slider for 5 times.

D - 3  Pull out the filter assembly from the dust compartment.

D - 4  Empty the dust compartment.

D - 5  Place back the filter assembly into the dust compartment.
 

 

 

 

Be sure to use the cleaner with the filter assembly at the dust  

  compartment.

D - 6  Set the dust compartment into the main body. Return dust  
 

 

compartment buckle to an original position. (Press until it "clicks")

D - 7  Unlock the Pre-filter and pull it up as illustrated.

D - 8  Remove the dust accumulated in the filter unit by tapping it  
 

 

against a hard surface lightly.

 

 

 

 

Don't clean the filter unit by brush or clean it with water.

D - 9  Reinstall the filter unit as per reverse procedure.

D - 10  Inspect once a month.
 

 

Using an old toothbrush or similar tool, clean any dirt or lint from  

  the 

brush.

D - 11  After removing the brush cover with a coin, remove the beater  
 

 

bar from the belt. Then cut across threads, strings, hairs, etc.  

 

 

from the beater bar with a pair of scissors. (Reinstall as per  

  reverse 

procedure)

 

 

 

 

Take care not to cut the brush.

 

 

Do not wash with water.

D - 12  Wipe with the soft cloth soaked with water.

D - 13  Push the dust compartment buckle and pull up the dust  
 

 

compartment from the main body.

D - 14  Remove the filter.

D - 15  Wash gently with water and then allow to dry in a shaded location.

D - 16  Replace to its original location.
 

 

 

 

Make sure you remember to replace the filter. If the filter is not  

 

 

install, it will cause motor failure.

 

 

Do not wash the filter in a washing machine or dry it with a dryer  

 

 

or other source of hot air.

Check that the appliance is correctly plugged in and that the socket 
outlet is working. In case that the thermal cut-off device has operated, 
wait until it resets after approximately 60 minutes. If after having 
checked the mentioned points, the cleaner does not work, take it to an 
Authorized Service Centre to be repaired.

• 

Stop the cleaner and unplug from the socket outlet.

• 

Check whether the wands, hose and accessories are blocked or  

 

not. If they are blocked, remove the obstruction.

• 

Check that the dust compartment is full. If it is full, empty it.

• 

Check that filter is blocked with dust. If it is blocked with dust, clean  

 it 

first.

The model and serial number of this product may be found on the name 
plate located at the underside of your cleaner. You should note that the 
model and serial number in the spaces provided and retain this book as 
a permanent record of your purchase.

Model number.  

______________________________________

Serial No. 

______________________________________

Date Purchased. 

______________________________________

Where Purchased. 

______________________________________

5

Power source

Max. input

Nominal input

Dimensions
(W x L x H)

Net weight

Extension wands

Floor nozzle

Crevice nozzle

Dusting brush

1600 W 

1250 - 1350 W

5 k

g

Metal x 2

2-Step

Telescopic

Turbine

230-240V ~ 50Hz

290mm x 425mm x 317mm

Telescopic

2-Step

√

√

1800 W

1350 - 1500 W

5.1 k

g