Panasonic SC-ZT2 Operating Guide

VQT2R71

Before requesting service, make the following checks.
If you are in doubt about some of the check points, or if the remedies indicated in the chart do not solve the problem, consult your 
dealer for instructions.

•  Ensure the AC mains lead connected.

14

“2CH SEARCH ” or “4CH 
SEARCH ” does not go off 
on the display while setting 
the speakers.

•  Make sure that the speakers are on.
 

 

If the display does not go off even when the speakers are on, consult your 
dealer.

15, 17

•  Select the correct source.
•  Turn the muting off.
•  Check that the digital signals can be decoded by this system.

With the optical fibre connection, cannot playback PCM signal with sampling 
frequency of over 96 kHz.

•  Check connections to other equipment.
•  (When the audio is not heard from TV) The optical fibre cable or stereo phono 

cable is necessary to connect with a TV incompatible with ARC. For details, 
refer to the operating instructions for the connected TV.

• Set “

AUTO ” in “Switching the input signal detection setting”.

•  Turn this system off then on again.
•  Make sure that the speakers are on.
•  Make sure that the speakers have been properly set.
•  Adjust the speakers.
•  If the connections are normal, this may be a cable-related problem. Use other 

cables and make connections again.

18
22
29

10 to 13

10

26

—

15, 17

16

22, 23

—

•  Replace the batteries if they are worn.
•  Make sure the remote control code has been properly set.

8

26

•  No sound is output from microphone if this system is digitally connected with DVD player. 

Change to analogue connection and input. Make analogue connection to AUX3 IN.

12, 13

•  Set the DTS Digital Audio Output setting on the DVD player, Blu-ray Disc 

player or DVD recorder to Bitstream.

• Set “

DTS ” in “Switching the input signal detection setting”.

—

26

•  This may occur due to digital copyright protection of the disc if using optical 

digital connection. This system may not be able to play sources with sampling 
frequency of over 48 kHz.

—

“F70 ††††” appears on 
the display.
(“DSP ” or “HDMI ” is 
displayed in †.)

•  Turn off the system, unplug the AC mains lead, and consult your dealer.

—

“F76 ” appears on the display.
(After displayed, the system 
turns off.)

•  Unplug the AC mains lead, and consult your dealer.

—

•  Set to Dolby Virtual Speaker, Dolby Pro Logic   or SFC.
•  (When the audio is not heard from TV) Check if this system is connected to TV 

with the optical fibre cable or the stereo phono cable properly.

19

10 to 12

•  You cannot use these features with PCM signals with sampling frequency of 

over 48 kHz. Make analogue connection to AUX3 IN.

•  You cannot use for Dolby Digital dual sounds.

12, 13

—

•  This may occur if you start play from a chapter on a DVD. The following will 

correct the problem.

1

 Change the audio output setting on the Blu-ray Disc player, DVD recorder or 

DVD player from Bitstream to PCM

 .

2

 Change input signal setting to “

PCM ” in “Switching the input signal detection setting”.

—

26

•  The system does not work properly if you have connected the HDMI input and output terminals 

incorrectly. Turn the system off, unplug the AC mains lead, and make the connection again.

10

•  When using this system in combination with TV (VIERA) only, check if HDMI 

cable is not connected to “BD/DVD IN” or “AUX1 IN” of this system. If it is 
connected to “BD/DVD IN” or “AUX1 IN”, connect to “TO TV (ARC)”.

—

•  This may occur when playing back 7.1-channel LPCM signals of a Blu-ray 

disc. Press [u SKIP] on the remote control of recorder or player to play back 
again from the beginning.

—