Panasonic ty-wk42pr2u Operating Guide

Before commencing work, carefully read these Instructions and the Manual for the wide plasma display to ensure

that fitting is performed correctly.

(Please save these instructions. You may need them when maintaining or moving the bracket.)

• Fit so that the arrow marks on the wall hanging bracket point upward.
• If the wall consists of a material such as concrete and bolts or nuts must be

embedded beforehand, determine the hole positions by aligning using the actu-
al wall hanging bracket, or calculate hole positions based on the dimension
drawing, and then embed "M6" bolts or nuts. When embedding bolts, locate so
that the bolts protrude from the wall by 10 to 15 mm (25/64 to 19/32 inches).

(1) Fasten the screw at the top center hole first.
(2) Using a level, correct any bracket inclination, and then fasten screws at

the remaining 5 locations.

• There are 14 holes in the wall hanging

bracket.
If the wall material is wood, and ade-
quate attachment strength cannot be
ensured by fastening at the 6 points at
right, use as many spare holes as
necessary. However, exercise care
because some wall materials may
crack if screws are located too close
together.

TQZH489

• Use commercially available M6 screws suited to the wall surface material

(wood, steel frame, concrete etc.) for fitting the bracket to the wall.

490 

(19 19/64

)

450 

(17 23/32

)

20 

(25/32

)

20 

(25/32

)

450 (17 23/32)

450 (17 23/32)

15 (19/32)

15 (19/32)

930 (36 5/8)

(1) Remove the red screws for open/close fastening (one

each on the left and right)

.

(2) Hook the insulation spacers on the top of the plasma

TV over the notches on the bracket, and allow the TV
to hang from the bracket.

(3) Pull the plasma TV body forward, as shown in the diagram

at right, and connect the wiring.

(4) After wiring is finished, slightly raise the plasma TV

and insert the insulation spacers at the lower back into
the holes at the base of the wall hanging bracket.

(5) Lower the plasma TV into place.

(1) Fit the included fastening screws in the indicated holes at

the sides of the wall-hanging bracket (left and right).

(2) Securely refit the red screws for open/close fastening

(one each on the left and right)

in the indicated holes

on the sides of the wall-hanging bracket.

Unit: mm (inches)

③

②

○

４

○

５

The angle of the wall-hanging bracket can be adjusted from
"no incline" to "20° incline" in 5 settings at intervals of 5°

(The TH-50PX20 has 4 settings, ranging up to "15° incline.")

The bracket is set to 5° before shipment from the factory. 
To change the angle, move the attachment position of the
strap.

* The strap is not needed for the "no incline" setting.

Web Site : http://www.panasonic.co.jp/global/

Allen head countersunk screw
Dished toothed washer
Insulation spacer
Allen wrench

* For detailed dimensions for attaching

the plasma TV, refer to the separate
External Dimension Drawing.

Place the plasma TV unit face down on a blanket or other soft cloth that is clean and free of debris, and follow the procedure below.

(1) Remove the terminal cover on the plasma TV (PX20 series only).
(2) Using a flathead screwdriver, remove the four caps from the plasma TV.

* Carefully retain the removed terminal cover

and caps in a safe place. (They will be needed
again later should it be required to use the
special-purpose stand or standalone stand.)

(3) Using the included Allen wrench, fit the

included Allen head countersunk screws,
dished tooth washers and insulation spacers
(4 sets) into the holes from where the caps
were removed. (See the diagram at right.)

• If the plasma TV is raised too far, there is a

risk it may become unhooked from the top
of the bracket.

• Do not hold the front panel of a PX20 Series

plasma TV at the bottom.

(1) Remove the screws for unit fastening (1 each on the left

and right) that are fitted to the wall hanging bracket sides.

(2) While lifting the bottom of the plasma TV unit, pull it towards

yourself.

(3) When the lower insulation spacers are freed, keep lifting

upward.

• Be sure to fit the fastening screws on the left

and right to keep the plasma TV from falling
off the wall-hanging bracket.

C

Matsushita Electric Industrial Co., Ltd.

2003