Panasonic SC-PM53 Operating Guide
RQTV0102
14
Troubleshooting guide
Before requesting service, make the below checks. If you canʼt fi x the system as described below, or if something not listed
here occurs, refer to the enclosed directory to locate an Authorized Service Center convenient to you or contact your dealer.
here occurs, refer to the enclosed directory to locate an Authorized Service Center convenient to you or contact your dealer.
Common problems
No sound.
Turn the volume up.
The speaker cables may not be connected properly. Turn the unit off, check and correct the
connections and turn the unit on (refer to page 4).
The speaker cables may not be connected properly. Turn the unit off, check and correct the
connections and turn the unit on (refer to page 4).
Sound is unfi xed, reversed or comes
from one speaker only.
from one speaker only.
Check the speaker connections (refer to page 4).
Humming heard during play.
An AC mains lead or fl uorescent light is near the cables. Keep other appliances and cords
away from this unitʼs cables.
away from this unitʼs cables.
“ERROR” is displayed.
Incorrect operation performed. Read the instructions and try again.
“– –:– –” appears on the display.
You plugged the AC mains lead in for the fi rst time or there was a power failure recently.
Set the time (refer to page 11).
Set the time (refer to page 11).
“F61” is displayed.
Check and correct the speaker cables connections (refer to page 4). Unplug and plug in the
AC mains lead, then turn on the unit.
If this does not fi x the problem, there is a power supply problem. Consult the dealer.
AC mains lead, then turn on the unit.
If this does not fi x the problem, there is a power supply problem. Consult the dealer.
Listening to the radio
Noise is heard.
The stereo indicator fl ickers or doesn’t
light.
Sound is distorted.
The stereo indicator fl ickers or doesn’t
light.
Sound is distorted.
Use an outdoor antenna (refer to page 5).
A beat sound is heard.
Turn the TV off or separate it from the unit.
A low hum is heard during AM
broadcast.
broadcast.
Separate the antenna from other cables and cords.
When there is a television set nearby
The picture on the TV
disappears or stripes appear
on the screen.
disappears or stripes appear
on the screen.
The location and direction of the antenna are incorrect. If you are using an indoor antenna,
change to an outdoor antenna (refer to page 5).
The TV antenna wire is too close to the unit. Separate the antenna wire of the TV set from
the unit.
change to an outdoor antenna (refer to page 5).
The TV antenna wire is too close to the unit. Separate the antenna wire of the TV set from
the unit.
Using the cassette deck
Recording is not possible.
If the erasure prevention tabs have been removed, cover the holes with adhesive tape (refer
to page 9).
to page 9).
Playing discs
The display is wrong or play
won’t start.
won’t start.
The disc may be upside down (refer to page 3).
Wipe the disc.
Replace the disc if it is scratched, warped, or non-standard.
Condensation may have formed inside the unit due to a sudden change in temperature. Wait
about an hour for it to clear and try again.
Wipe the disc.
Replace the disc if it is scratched, warped, or non-standard.
Condensation may have formed inside the unit due to a sudden change in temperature. Wait
about an hour for it to clear and try again.
The total number of tracks displayed
differs each time the same disc is
inserted.
Unusual sound is heard.
differs each time the same disc is
inserted.
Unusual sound is heard.
The disc may be scratched, or its data may be defective. Replace the disc.
CD-RW cannot be read.
The disc was incompletely formatted. Use the recording equipment to fully format the disc
before recording.
before recording.
“VBR–” is displayed instead of the
remaining play time.
remaining play time.
The unit cannot display the remaining play time for variable bit rate (VBR) tracks.
“TAKE OUT/DISC” appears on the
display.
display.
There is a problem with the disc mechanism. (A power failure may have occurred.)
The tray will open automatically. Remove the disc from the tray, and after ensuring there is
no disc in the tray, close it. The unit will make the disc changing noises for a few moments
and then it should operate normally.
The tray will open automatically. Remove the disc from the tray, and after ensuring there is
no disc in the tray, close it. The unit will make the disc changing noises for a few moments
and then it should operate normally.
The remote control
Remote control doesn’t work.
Check that the batteries are inserted correctly (refer to page 5).
Replace the batteries if they are worn.
Replace the batteries if they are worn.
RQTV0102_1B.indd 14
RQTV0102_1B.indd 14
2/6/06 12:01:31 PM
2/6/06 12:01:31 PM