Panasonic SB-ZT1 Operating Guide

RQT9462

As this system uses a frequency band of 2.4 GHz, the radio waves 

may be interrupted by an obstacle. Depending on the surrounding 

environment (i.e. radio wave interruption from outside, etc.) or the 

building structure where this system is used (i.e. wall that easily 

reflects radio waves, etc.), sounds may be cut or noise may occur.

Install this system properly paying attention to the following descriptions.

As this system received Technical Conditions compliance certifi cation 

based on the Radio Law, the wireless station license is not required. 

However, if you do the following actions to this system, you may be 
punished by law.

•  Domestic use only.

•  Use this system in the same room.

 Do not place an obstacle between the main unit (SC-ZT1) and 

Radio waves from this system reach maximum range of 15 m in the 

same room. If there is an obstacle between the main unit (SC-ZT1) and 

speakers or the main unit (SC-ZT1) is placed at the height of 50 cm or 

below from the floor, the radio waves reach smaller range.

If the following equipment is located near the system, install this 

system away from such equipment.

This system is designed to automatically avoid radio wave interference 

with such household equipment. If radio wave interference occurs, the 

Wireless Link display (

➜ page 16 of SC-ZT1 Operating Instructions) 

may blink, the sounds from speakers may be interrupted or noise may 

occur.

These phenomena occur when this system selects a proper 

frequency. These are not malfunctions.

If there are metal objects or furniture in the room where this system is 

installed, radio waves tend to be reflected. Depending on the listening-

viewing position, sounds may be interrupted or noise may occur.  These 

symptoms may be remedied by slightly moving this system’s position.

Note that radio waves tend to be reflected also when this system is 

installed in rooms with a lot of activity.

 When carrying speakers, hold the pole and base parts. (➜ below)

 The speakers of this system are not magnetically shielded. Do 

•  Make sure the base parts are not covered by cloth such as a curtain.

•  Before attaching the leg cushion (included) on the base parts to 

prevent tilt or rattle on the floor, make sure there are no people in 

the surrounding area.

•  Set the distance from each speaker to the listening-viewing position. 

(

➜ page 24 of SC-ZT1 Operating Instructions)

Front speaker 

(right)

Front speaker 

(left)

Connected equipment

Main unit

Surround 

speaker 

(left)

Surround 

speaker (right)

Approx.120°

•  Place the surround speakers slightly at the back right and left of the listening-viewing position.

Please check and identify the supplied accessories.

Use numbers indicated in parentheses when asking for replacement parts.

(Product numbers correct as of April 2009. These may be subject to change.)

Supplied accessories differ depending on the symbols 

(E, GN, GS) indicated on the packaging box.

Use correct accessories according to the region for use.

AC IN

TEST

ID

2

1

TEST terminal: This is used to check the product operation status. 

Only used in factory. Do not insert a foreign object.

ID switch: This is used to check the product operation status and not 

used regularly.

WIRELESS LINK

AC inlet (➜ left)

1

[WIRELESS LINK] indicator (➜ right 

page)

When the unit is connected to the AC mains 

supply, this indicator lights red in standby mode 

and lights green when the unit is turned on.

2

Unit on/off button (l ^ k I) (➜ right page)

Use this button to turn the unit on and off.

l (off): The unit is in standby mode.

k (on): The unit is on. 

The unit is still using a small amount of power in 

the standby. Standby uses less power.

2 AC mains leads

(For continental Europe)

(K2CQ2CA00007)

(For the United Kingdom and Republic of Ireland)

(K2CZ3YY00005)

(For Australia and New Zealand)

(K2CJ2DA00010)

(For Saudi Arabia, Kuwait, 

Malaysia and Hong Kong)

(K2CZ3YY00005)

(For Thailand)

(K2CP2CA00001)

(For others)

(K2CQ2CA00007)

2 AC mains lead adapters (K2DAYYY00002)

If AC mains leads will not fit your socket, use AC mains lead adapters.

Leg cushions (1 sheet: 8 pieces) (RFA3045)

Keep the leg cushion out of reach of children to prevent swallowing.

AC IN

To save power when the system is not to be used for a long time, 

unplug it from the household mains socket.

Make sure to turn this system off before unplugging the AC mains lead.

For power consumption of speakers in standby, see right.

Power supply differ depending on the symbols (E, GN, GS) indicated on the packaging box.

Even when the connector is perfectly 

inserted, depending on the type of inlet used, 

the front part of the connector may jut out as 

shown in the drawing.

However there is no problem using the system.

Approx. 

6 mm

Appliance inlet

Connector

The included AC mains leads are for use with this system only. Do not use them with 

other equipment. Also, do not use AC mains lead for other equipment with this system.

Refer to page 3 for Sales and Support Information (for the United Kingdom and Republic of lreland).