Panasonic SA-XR55 Operating Guide
RQT7997-1B
H0405RT1055
Matsushita Electric Industrial Co., Ltd.
Web Site: http://www.panasonic.co.jp/global/
En
Troubleshooting guide
Before requesting service, make the below checks.
If you can’t fix the unit as described or if something not listed here occurs, contact your dealer.
If you can’t fix the unit as described or if something not listed here occurs, contact your dealer.
n
Common problems
Pages
No power.
• Ensure the AC mains lead is connected.
8
No sound.
Sound is distorted.
Sound is distorted.
• Turn the volume up.
• Check connections to speakers and other equipment.
• Turn on the speakers.
• Select the correct source.
• Change D-INPUT setting to suit the type of connection you have made.
• Check that the digital signals can be decoded by this unit.
• Turn the muting off.
• Turn PCM FIX off.
• Recording of some DVD-Audio may not be possible due to copyright protection.
• Check connections to speakers and other equipment.
• Turn on the speakers.
• Select the correct source.
• Change D-INPUT setting to suit the type of connection you have made.
• Check that the digital signals can be decoded by this unit.
• Turn the muting off.
• Turn PCM FIX off.
• Recording of some DVD-Audio may not be possible due to copyright protection.
14
4 to 11
14
14
13
15
20
13
14
13
15
20
13
–
Sound stops. “OVERLOAD ”
appears on the display for
about a second and the unit
turns off.
appears on the display for
about a second and the unit
turns off.
• Determine and correct the cause, then turn the unit on.
Causes include:
- Shorting (bare wires touching) of positive and negative speaker wires.
- Using speakers with an impedance lower than that rated for this unit.
- Straining of the speakers through excessive volume or power.
- Using the unit in a hot environment without proper ventilation.
- Using speakers with an impedance lower than that rated for this unit.
- Straining of the speakers through excessive volume or power.
- Using the unit in a hot environment without proper ventilation.
Consult your dealer if the problem occurs again after switching the unit on.
7
7, 8, 26
–
–
–
“F76 ” appears on the display
and the unit turns off.
and the unit turns off.
• Turn the unit off, disconnect the AC mains lead, and consult your dealer.
–
“F70 ” appears on the display.
• Turn the unit off, disconnect the AC mains lead, and consult your dealer.
–
“U12 ” appears on the display.
• Match the “Remote control mode” on the main unit and the remote control.
25
Display is dim.
• Cancel “
DIMMER ”.
19, 20
Clicking sound heard during
play.
play.
• Depending on the input signal when playing DVD etc., the DUAL AMP function changes
automatically. A clicking sound is heard when it changes. This does not mean a problem
with the unit.
with the unit.
15
n
Sound effects
Pages
Sound is not heard from the
center, surround or subwoofer
speakers.
center, surround or subwoofer
speakers.
• Ensure the speaker settings for your speakers are correct.
• The source may be stereo. Turn Dolby Pro Logic
• The source may be stereo. Turn Dolby Pro Logic
, DTS NEO:6 or SFC on.
• If the FRONT speakers are set to LARGE:
- When you play an analogue or PCM source in stereo, sound is output from the subwoofer.
However when you play a Dolby Digital or DTS 2-channel source in stereo, only the LFE
(low frequency effects channel) signal from the source is output from the subwoofer.
(low frequency effects channel) signal from the source is output from the subwoofer.
12, 21
15
21
21
Sound is not heard from the
surround back speaker.
surround back speaker.
• Ensure the speaker settings for your speakers are correct.
• Turn Dolby Pro Logic
• Turn Dolby Pro Logic
, DTS NEO:6 or SFC on.
12, 21
15
Cannot use Dolby Pro Logic
,
DTS NEO:6 or SFC.
• Turn DVD ANALOG 6CH off.
• You cannot use Dolby Pro Logic
• You cannot use Dolby Pro Logic
, DTS NEO:6 or SFC when input is PCM with sampling
frequencies of 192 or 176.4 (COAXIAL1).
14
–
There is no DTS audio output.
There is audio output, but the
DTS decoder indicator is not lit.
There is audio output, but the
DTS decoder indicator is not lit.
• Set the DTS Digital Audio Output setting on the DVD player or DVD recorder to
“Bitstream”.
–
Sound is distorted when using
the Sound Field Control (SFC).
the Sound Field Control (SFC).
• Depending on the input source, sound may be distorted if you increase the SFC speaker
level or effect. If this happens, decrease the SFC speaker level or effect.
18
n
Radio
Pages
The radio cannot be tuned in
or there is a lot of noise and
interference.
or there is a lot of noise and
interference.
• Connect the appropriate antenna. (You may need an outdoor antenna or one with more
elements.)
• Adjust the position of the FM or AM antenna.
• Reduce the treble.
• Turn off nearby televisions, video decks, DVD players, and satellite receivers.
• Separate the antenna from other cables, cords, and appliances.
• Reduce the treble.
• Turn off nearby televisions, video decks, DVD players, and satellite receivers.
• Separate the antenna from other cables, cords, and appliances.
11
11
19
19
–
–
–
There is a lot of noise when
listening to AM.
listening to AM.
• Try changing the BEAT PROOF mode.
23
The correct AM frequency
cannot be tuned in.
cannot be tuned in.
• Change the frequency step to suit your area when AM is selected.
22
n
Remote control
Pages
The remote control doesn’t
work.
work.
• Replace the batteries if they are worn.
11
Other products respond to the
remote control.
remote control.
• Change this unit’s remote control mode to “
REM2 ”.
25