Panasonic SA-XR700 Operating Guide

RQT8743

Before requesting service, make the following checks. If you are in doubt about some of the check points, or if the remedies indicated in the chart do not

solve the problem, consult your dealer for instructions.

• Ensure the AC mains lead is connected.

• Turn the volume up. 

• Check connections to speakers and other equipment. 

• Turn on the speakers.

• Select the correct source. 

• Change DIG INPUT setting to suit the type of connection you have made. 

• Check that the digital signals can be decoded by this unit. 

• Turn the muting off.

• Turn PCM FIX off.

• Recording of some DVD-Audio may not be possible due to copyright protection.

“OVERLOAD ” appears on the 

• Determine and correct the cause, then turn the unit on. 

Causes include:

- Shorting (bare wires touching) of positive and negative speaker wires. 

- Using speakers with an impedance lower than that rated for this unit. 

- Straining of the speakers through excessive volume or power.

- Using the unit in a hot environment without proper ventilation. 

á 

Consult your dealer if the problem occurs again after switching the unit on.

the message “OVERFLOW ” appears on 

• Switch the attenuator on.

“F76 ” appears on the display and 

• Turn the unit off, disconnect the AC mains lead, and consult your dealer.

“F70 ” appears on the display.

• Turn the unit off, disconnect the AC mains lead, and consult your dealer.

“REMOTE 2 ” or “REMOTE 1 ” 

• Match the codes on the main unit and the remote control.

• Cancel “

DIMMER ”.

• Depending on the input signal when playing DVD etc., the ADVANCED DUAL AMP function changes

automatically. A clicking sound is heard when it changes. This does not mean a problem with the unit.

á 

You can also set the unit against automatic ADVANCED DUAL AMP operations.

“MEASURING ERROR ” appears 

• A speaker is too far. Check speaker locations.
• An error occurred from a cause that cannot be identified. Perform the auto speaker setup again.

When speaker distances are set (á page 

33), “– ” appears on the display with the 

speaker name such as “L 3.0 – ”.

• It appears when polarity of a speaker is automatically adjusted.
á 

You can set speakers against automatic polarity adjustment.

When speaker distances are set (á page 

33), “OVER ” appears on the display.

• It appears when the measured distance exceeds 15 meters.

Check the speaker location.

• Ensure the speaker settings for your speakers are correct.

• Confirm Dolby Pro Logic 

, NEO:6, or SFC settings, and select an adequate mode.

• Press [SURROUND] on when you play 2-channel stereo sources.

• Ensure the speaker settings for your speakers are correct.
• Press [SURROUND] on.

• Check if the center speaker, surround speakers, and surround back speakers are connected properly.

• Press [SPEAKERS A] on.

• You cannot use Dolby Pro Logic

, NEO:6 or SFC on sources containing PCM signals with the sampling

frequency of 192 kHz.

• Cancel DVD ANALOG 6CH playback.

• You cannot use the effect when the input source contains dual audio signals in Dolby Digital or DTS formats.

• Set the DTS Digital Audio Output setting on the DVD player or DVD recorder to “Bitstream”.

• Depending on the input source, sound may be distorted if you increase the SFC effect level. If this

happens, decrease the SFC effect level.

• Connect the appropriate antenna. (You may need an outdoor antenna or one with more elements.)

• Adjust the position of the FM or AM antenna.

• Reduce the treble.

• Turn off nearby televisions, video decks, DVD recorders, DVD players, and satellite receivers.

• Separate the antenna from other cables, cords, and appliances.

• Try changing the BEAT PROOF mode.

• Change the frequency step to suit your area when AM is selected.

• Should you be playing a chapter on a DVD:

- Change the audio output setting on the DVD player or DVD recorder from “Bitstream” to “PCM”. 

(6.1-channel sources will however be played as 5.1-channel.)

- Select “

PCMFIX ” as instructed in “Setting input signals” when you play 2-channel stereo sources.

“U70-1-1 ” appears on the display.

• The equipment connected by the HDMI cable is not compatible with the unit’s copyright protection technology.

“U70-1-2 ” appears on the display.

• The unit has received a signal for a picture format that is incompatible with the HDMI connection. Check

the settings of the connected equipment.

“U70- 3 ” appears on the display.

• Should anything unusual happen using an HDMI connection:

Consult your dealer if the sign remains on the display after these steps.

- Turn the connected equipment off and on again.

- Pull out the HDMI cable then reinsert it.

- Reduce the number of equipment connected in series to the HDMI terminal if exceeding 2 units.

• The unit does not work properly when wrong cords are in HDMI input and output terminals. Turn the unit

off, unplug the AC mains lead, and make connections again.

• Connect the unit to your TV (VIERA) using the HDMI cable, switch the TV on, unplug the unit’s AC mains

lead, and insert it into a household mains socket again.

• Some of the linked operations apply to the connected equipment that is HDAVI Control compatible. To

prevent this, set the connected equipment (DVD recorder (DIGA) and others) against HDAVI Control.

• Replace the batteries if they are worn.

• Change this unit’s remote control code to “

REMOTE 2 ”.

SA_XR700_EG_GN_ (RQT8743_B)ver.3.fm  45 ページ  ２００６年８月３１日　木曜日　午前９時７分