Panasonic DMREZ28 Operating Guide
63
RQT9118
Ref
erence
Messages
On the Unit’s Display
Page
H , F
(“ ” stands for a service number.)
(“ ” stands for a service number.)
An error has occurred. The number following “H” or “F” depends on the
status of the unit. Check the items below and in the Troubleshooting Guide.
If the service number still does not disappear after the check, reset the unit
(
status of the unit. Check the items below and in the Troubleshooting Guide.
If the service number still does not disappear after the check, reset the unit
(
➔ 65, “To restore the unit if it freezes” ).
If the service numbers fail to clear, note the service numbers and contact a
qualified service person.
qualified service person.
•
•
−
−
DVD
(“ ” stands for a number.)
(“ ” stands for a number.)
The remote control and the main unit are using different codes. Change the
code on the remote control.
code on the remote control.
•
65
GUIDE
TV Guide data is being downloaded.
•
56
HARD ERR
※
If there is no change after turning the unit on and off, consult the dealer where
the unit was purchased.
the unit was purchased.
•
−
NoERAS
You cannot delete items on this disc.
The disc may be damaged. Use a new disc.
The disc may be damaged. Use a new disc.
•
−
NoREAD
The disc is dirty or badly scratched. The unit cannot record, play, or edit.
The disc may be incompatible or of poor quality.
You have used a lens cleaner and it has finished operation. Press [; OPEN/
CLOSE] on the main unit to eject the disc.
The disc may be incompatible or of poor quality.
You have used a lens cleaner and it has finished operation. Press [; OPEN/
CLOSE] on the main unit to eject the disc.
•
•
•
•
•
13
13, 14
64
NoWRIT
You cannot write to this disc.
The disc may be damaged. Use a new disc.
The disc may be damaged. Use a new disc.
•
−
FINAL
When the screen asking if you want to finalise the disc appears, the message
is displayed.
is displayed.
•
23
PLEASE WAIT
※
Displayed when the unit is started. This is not a malfunction.
The unit is carrying out its recovery process. You cannot operate the unit while
the message is displayed.
The unit is carrying out its recovery process. You cannot operate the unit while
the message is displayed.
•
•
•
−
−
−
PROG FULL
※
There are already 16 timer recording programmes. Delete unnecessary timer-
recording programmes.
recording programmes.
•
29
SW-DL
The unit is performing a software update.
•
56
UNSUPPORT
※
You have inserted a disc the unit cannot play or record onto.
•
13, 14
UNFORMAT
※
You inserted an unformatted DVD-RAM, DVD-RW, +RW, an unused +R, +R DL
or DVD-RW (DVD-Video format) that has been recorded on other equipment.
Format the disc to use it.
However all the recorded contents on the disc are deleted.
or DVD-RW (DVD-Video format) that has been recorded on other equipment.
Format the disc to use it.
However all the recorded contents on the disc are deleted.
•
48
F74
The HDMI connection could not be authenticated due to a transfer malfunction.
Consult the dealer where the unit was purchased.
Consult the dealer where the unit was purchased.
•
−
F75
The HDMI connection could not be authenticated due to an internal data
malfunction.
Consult the dealer where the unit was purchased.
malfunction.
Consult the dealer where the unit was purchased.
•
−
U59
The unit is hot.
The unit switches to standby for safety reasons. Wait for about 30 minutes until
the message disappears.
Select a position with good ventilation when installing the unit. Do not block
the cooling fan on the rear of the unit.
The unit switches to standby for safety reasons. Wait for about 30 minutes until
the message disappears.
Select a position with good ventilation when installing the unit. Do not block
the cooling fan on the rear of the unit.
•
−
U61
(When a disc is not inserted) Displays when a malfunction has occurred.
This is displayed when the unit is in the recovery process to return to normal
operation; it is not broken. Once the display disappears you can use the unit
again.
This is displayed when the unit is in the recovery process to return to normal
operation; it is not broken. Once the display disappears you can use the unit
again.
•
−
U76
HDMI cannot be output because you are connected to a model that does not
support copyright protection.
support copyright protection.
•
−
U80
U81
U99
U81
U99
The unit fails to operate properly. Press [8] on the main unit to switch the unit
to standby mode. Press [8] on the main unit again to turn the unit on.
to standby mode. Press [8] on the main unit again to turn the unit on.
•
−
U88
There was something unusual detected with the disc while recording or playing;
there was a power failure or the AC mains lead was disconnected while the unit
was on. The unit is carrying out its recovery process. This process restores the unit
to normal operation. The unit is not broken. Wait until the message disappears.
there was a power failure or the AC mains lead was disconnected while the unit
was on. The unit is carrying out its recovery process. This process restores the unit
to normal operation. The unit is not broken. Wait until the message disappears.
•
67
X HOLD
The Child Lock function is activated.
Press and hold [OK] and [RETURN] at the same time until “X HOLD” disappears.
Press and hold [OK] and [RETURN] at the same time until “X HOLD” disappears.
•
57
※ The message is alternately displayed.
DMR-EZ28-EB _RQT9118-B.indb 63
DMR-EZ28-EB _RQT9118-B.indb 63
2008/04/04 10:32:33
2008/04/04 10:32:33