Panasonic DMREX769EB Operating Guide

27

RQT9307

[HDD] [RAM] [-R] [-RW‹V›] [+R] [+RW]

Tips

To skip unwanted parts
Press [] to pause recording. (Press again to restart recording.)
To stop recording
Press [].

Tips

To cancel the external control
Press [EXT LINK] to stop recording or to cancel linked timer recording 
standby (The unit turns on and ‘‘EXT-L” disappears.).
Manual timer recordings (¼ 28)

Notes

 In order to prevent accidental operation, press [EXT LINK] to cancel 

the setting after recording is fi nished.

 This function does not work when “TV System” is set to “NTSC” in 

the setup menu (¼ 65).

 This function does not work with some equipment. Refer to the 

equipment’s operating instructions.

 The beginnings of recordings may not be recorded correctly in some 

cases.

 When “Ext Link” is set to “Ext Link 2”, this function does not work if 

the input signal is NTSC system.

 Programmes are recorded as one title on this unit when the end 

time of the earlier timer recording and the start time of the later timer 
recording are close to each other.
[HDD] [RAM] To divide the titles, go to “Divide Title” (¼ 46).

 When this unit is in EXT LINK standby (“EXT-L” is shown on the 

unit’s display), the TV Guide data cannot be downloaded.

 While the unit is in EXT LINK standby mode or recording, AV1 output 

terminal outputs the signal which is input from the AV2 input terminal 
irrespective of “AV1 Output” setting (¼ 65).

 During EXT LINK standby mode or recording, playback is only 

available from the drive performing the recording.

 When “EXT-L” lights on the unit’s display, Direct TV Recording is 

unavailable.

To record programmes from a SKY Digital STB/digital 
satellite receiver using timer programming

 This unit cannot record NTSC signals to discs that 

already have PAL signal recordings. (However, both 
types of programmes can be recorded onto the HDD.)

Preparation:
 ]RAM\ If the disc is protected, release protection

(¼ 58).

 Connect a digital satellite receiver to this unit’s AV2 

input terminals (¼ 11).

 When the output signal from the external equipment 

is NTSC, change the “TV System” to “NTSC” in the 
Setup menu (¼ 65).

With the unit stopped

 

SELECT

INPUT

 to select “AV2” for the 

digital satellite receiver you have 
connected.

 

 DRIVE
SELECT

  to select the HDD or DVD 

drive.

− If you selected the DVD drive, insert a disc

(¼ 17). 

 

REC MODE

 to select the recording 

mode.

  Select the channel on the digital 

satellite receiver. 

 

REC

 to start recording.

Preparation:
 ]RAM\ If the disc is protected, release protection

(¼ 58).

 Make sure you connect the AV2 terminal of this unit 

to “VCR Scart Terminal” of a SKY Digital STB/digital 
satellite receiver with a 21-pin scart cable (¼ 11).

 Set the “AV2 Input” and “Ext Link” to match the 

connected equipment in the Setup menu (¼ 65).

  Make timer programming on 

SKY Digital STB/digital satellite 
receiver.

− Refer to the equipment’s operating instructions. 

 

 DRIVE
SELECT

  to select the HDD or DVD 

drive.

− If you selected the DVD drive, insert a disc

(¼ 17). 

 

EXT LINK

− The unit turns off and “EXT-L” lights on the 

unit’s display to indicate timer recording 
standby has been activated.

− While the unit is in EXT LINK standby mode 

or recording, most operations on this unit are 
prohibited ([ OPEN/CLOSE], [/l] etc.).
When you operate, press [EXT LINK] to 
cancel EXT LINK standby mode or recording 
(The unit turns on and “EXT-L” disappears.).

DMR-EX769EB.indb   27

DMR-EX769EB.indb   27

2009/01/26   17:06:11

2009/01/26   17:06:11