Panasonic PVV4624SK Operating Guide

*Important:

If a remote control button does not work when pressed,
press the VCR button on the remote and try the button again.

- 7 -

Press PROG* to display program screen.

Press PROG to end programming.

press   to set START/ STOP times, CH (channel) or
LINE input (p. 9 of Advanced Operations book), and
tape speed (p. 3).
Then press 

 to select.

1) Press  .
2) Set record DATE,

 to select:

1~31= one time,
or DAILY= Monday~Friday,
or WEEKLY= same time
each week (see right).

 to select and press   to set an unused program.

Then repeat step 2. Or, press PROG to exit.

Example

Today

 to select

desired program.

Press POWER off to set the timer recording. (“TIMER” lights on Multi Function Display.)

Press PROG
to display program screen.

Press PROG to end the programming.

• If a power interruption occurs while programming the timer, the timer program(s) may be cancelled.

If “TIMER PROGRAMS WERE LOST DUE TO POWER INTERRUPTION” appears on-screen,
please re-enter the timer programs.

• When recording programs via DSS receiver, DSS receiver must be left on.
• When recording programs via an antenna or cable, DSS receiver must be turned off.

1) Press   to display.
2) Repeat Step 2

(p. 6) to set new
programs.

Press ADD/DLT.

Press POWER and then STOP within 10
seconds to cancel the Timer Recording.

(The TIMER indicator goes out on Multi
Function Display.)

- 6 -

DAILY

7

2

1

31

6

8    9

WEEKLY

(SA)

WEEKLY

(MO)

WEEKLY

(SU)

P DT START    STOP    CH   SPD

1 13   2:00p   3:20p  02  SLP

2 14   7:00p   7:30p  10    SP
3 -- --:--  --:--  --   --
4 -- --:--  --:--  --   --

 
SELECT :              SET :
EXIT

: PROG

P DT START    STOP    CH   SPD

1

 13   2:00p   3:20p  02  SLP

2 -- --:--  --:--  --   --
3 -- --:--  --:--  --   --
4 -- --:--  --:--  --   --

CANCEL : ADD/DLT 
SELECT :              SET :
END

: PROG

SET  COMPLETED

P DT START    STOP    CH   SPD

1

 -- --:--  --:--  --   --

2 -- --:--  --:--  --   --
3 -- --:--  --:--  --   --
4 -- --:--  --:--  --   --

 
SELECT :              SET :
END

: PROG

P DT START    STOP    CH   SPD

1

 -- --:--  --:--  --   --

2 14   7:00p   7:30p  10    SP
3 -- --:--  --:--  --   --
4 -- --:--  --:--  --   --

 
SELECT :              SET :
END

: PROG

This video recorder, equipped with HQ
(High Quality) system, is compatible with
existing VHS equipment. Only use tapes
with the 

 mark. Only tapes tested and

inspected for use in 2, 4, 6, and 8 hour
machines are recommended.

*Important: If a remote control button does not work when pressed,

press the VCR button on the remote and try the button again.

- 5 -

Insert a tape with a record tab (p. 3).

Press PLAY to play tape.

• If tape has no rec. tab (p. 3), auto play begins.

• Loose or peeling labels

• These features work best in SP or SLP mode.
• The sound will be muted.
• To reduce picture noise, see “Manual

Tracking Control” on p. 3.

• After 3 minutes in Still or Slow mode, VCR

stops to protect the tape and the video heads.

Press REW or FF in Stop mode to
rewind or fast forward tape.

Press EJECT on remote,
or STOP/EJECT on VCR to eject  tape.

Press STOP to stop tape.

• Picture interruption may occur with some TVs.
• FF and REW search speed may vary depending on

current tape position.

• After 10 minutes in search mode, VCR returns to

Play mode to protect the tape and the video
heads.

Insert a tape 

➛ Power comes on ➛ Play starts if there is no record tab (see p. 3).

Play
Fast Forward

(Repeat Play must be off)

Play 

➛ Tape end ➛ Rewind ➛ Stop➛ Tape ejects if there is no record tab

➛ Tape end ➛ Rewind ➛ Stop

➛

➛

➛

➛

➛ VCR ➛

➛

➛

➛

➛ TV

➛

➛

➛

➛

➛ VCR ➛

➛

➛

➛

➛ TV

1

2

1

2

Plugging the VCR Power Cord into an AC wall outlet starts auto channel and clock set.

If you use a cable box, turn it on and set it to the
Public Broadcasting Station (PBS) channel in
your time zone. If you use a DSS receiver, it
must be turned off.

If Auto Clock Set was incomplete.

DST : ON

1 /  1/2004   THU

--

 -

12:00PM

- - - - - - - - -- - - - - - - -- - - - - - 

SET  CLOCK

SELECT :                SET : 
END

: ACT I ON     

- 4 -

DST : ON

6 /20/2004   SUN

-

 -

15:30PM

- - - - - - - - -- - - - - - - -- - - - - - 

SET  CLOCK

SELECT :                SET : 
START

: ACT I ON     

IN FROM ANT.

TV

VCR

VHF/UHF

OUT  TO  TV

IN from
ANT./CABLE

1

2

IN FROM ANT.

TV

VCR

VHF/UHF

OUT  TO  TV

IN from
ANT./CABLE

Cable TV
Converter Box

1

2

on your new purchase! With proper use, this
dependable product will provide years of
enjoyment. Please fill in the information below.
(Serial number is on tag on back of VCR.)

• Date of Purchase

• Dealer Purchased From

• Dealer Address

• Dealer Phone No.

• Model No.                 

• Serial No.

- 3 -

Old or damaged tapes may clog heads.

V I DEO  HEADS  MAY
NEED  CLEAN I NG
PLEASE   I NSERT  HEAD
CLEAN I NG  CASSETTE
OR  REFER  TO  MANUAL

END               : PLAY

- 2 -

AUTO  CLOCK  SET 

IS  I NCOMPLETE

PLEASE  SET  CLOCK  BY
PRESSING  ACT I ON  KEY

to select the channel.

• If channel number is over 100, first press 100

key then the other 2 digits.

• For “LINE” input, see p. 9 of “Advanced

Operations” book.

Press SPEED to set record speed (p. 3).

Press REC to start recording.

• To edit, press PAUSE/SLOW to pause, and

again to resume recording.

Press STOP to stop recording.

One Touch Recording
(recording in progress)

Press REC repeatedly to set length as follows:
30 min. 

➛

 1 hr. 

➛

 1:30 

➛

 2:00 

➛

 3:00

➛

 4:00 

➛

 exit.

The VCR shuts off at the length set.

Press VCR/TV
(“VCR” goes out on Multi Function Display),

➛

 select channels on TV (recording continues).

Press VCR/TV in Stop or Pause mode.
(“VCR” lights on Multi Function Display),

➛

 select channels on VCR.

• After 5 minutes in Pause mode, VCR stops to

protect the tape and the video heads.

• Function buttons are void during Initial Setup.
• To eject a tape during Auto Set, press EJECT

on remote or STOP twice on VCR.
Then make settings manually. (See p. 11.)

• If Auto Clock Set takes more than 30 minutes,

press STOP and perform settings manually.
 (See p. 11.)

• Rewinds a T-120 tape in approx. 1 minute.

P DT START    STOP    CH   SPD

1 

13   2:00p   3:20p  02  SLP

2 14   7:00p   7:30p  10    SP
3 -- --:--  --:--  --   --
4 -- --:--  --:--  --   --

CANCEL : ADD/DLT 
SELECT :              SET :
END

: PROG

Automatically controls the video output signal for
less noise depending on the tape condition.

Continuously analyzes the signal and adjusts for
optimum picture quality.

(to reduce picture noise)
Use during Playback and Slow Motion mode to
reduce picture noise.
Press CH (TRACKING)  /  on the remote
control or on the VCR until the picture clears up.
To return to Auto Tracking, press POWER off,
then on again a few seconds later.

In Still mode, CH (TRACKING)  /  operate as a
V-Lock control.

R

R

R

R

R

R

R

R

Use soft, dry cloth or dusting attachment of a
vacuum to remove dust from all cabinet vent
holes. You may moisten cloth with non-abrasive,
antistatic cleaner/ polisher.
Caution:
Alcohol and various solvents could damage finish.

Over tightening “Nut type” RF coaxial cables
may damage jacks. Finger tighten only.

• SP = Standard Play
• SLP = Super Long Play

Note: Designs and specifications are subject to

change without notice.

120 V AC, 60 Hz

Power On
Approx. 18 W
Power Off
Approx. 0.95 W

EIA Standard NTSC colour

4 rotary heads helical

scanning system

1 track (Normal)
2 channel (Hi-Fi Audio Sound)

Tuner
 Broadcast Channels: VHF 2 ~ 13, UHF 14 ~ 69
 CABLE Channels:

Midband A ~ I (14 ~ 22)
Superband J ~ W (23 ~ 36)
Hyperband AA ~ EEE
(37 ~ 64)
Lowband A-5 ~ A-1 (95 ~ 99)
Special CABLE channel 5A (01)
Ultraband 65 ~ 94, 100 ~ 125

5 °C ~ 40 °C (41 °F ~ 104 °F)

Operating Humidity: 10 % ~ 75 %
Weight:

2.55 kg (5.6 lbs).

430 (W) x 98 (H) x 240 (D) mm
16-15/16” (W) x 3-7/8” (H) x
9-7/16” (D) inch

• If screen below does not appear...

check all connections.
Try tuning TV to channel 4.

• To change VCR’s output channel, please

refer to “VCR’s Output Channel” (p. 11).

• If wrong language is set, do “Reset All VCR

Memory Functions” (p. 10).

Select language
Press 1 : English
Press 2 : French
Press 3 : Spanish

AUTO  CLOCK  SET
     
     PROCEEDING

CANCEL : STOP

CH  AUTO  SET  PROCEEDING

CANCEL : STOP

SELECT   LANGUAGE

ENGL I SH

:PRESS

1

FRANÇA I S

:APPUYER

2

ESPAÑOL   

:OPR I M I R

3

To record again

Break off the tab to
prevent recording.

Record Tab

Screw driver

Cover the hole
with cellophane
tape.

• Tapes recorded in S-VHS can easily be played

back using the same procedure as with VHS
tapes.

• This VCR automatically distinguishes between

S-VHS and VHS tapes and plays them back.

• Picture quality will be normal VHS, not

S-VHS and picture noise may occur.
(Colour loss or picture disruption during
Search, Pause, etc. is normal.)

• S-VHS recording is not possible.

RF Coaxial Cable

LSJA0418

Batteries 2 “AA”

Remote Control

LSSQ0407

• Do not mix old and new batteries.
• Do not mix alkaline with manganese batteries.

1) Open cover.

3) Close cover.

2) Insert batteries as

marked.

SP

(Standard Play)

2 Hours

40 Minutes

2 Hours

6 Hours

8 Hours

SLP

(Super Long Play)

3 Hours

9 Hours

Only use tapes with the 

 mark in this unit.

• Tapes recorded in S-VHS can easily be

played back with normal VHS quality (p. 5).

➛ Press PAUSE/SLOW.

➛ Press PLAY to release.

➛ Hold down PAUSE/SLOW in Still mode.

➛ Press PLAY to release.

➛ Press FF or REW.

➛ Press PLAY to release.
After search has begun, each additional
press of FF or REW changes speed.

Operate only from a power source indicated on the unit
or in this manual. If necessary, have your Electric Utility
Service Company or Video Products Dealer verify the
power source in your home.

As a safety feature, this Video product comes with
either a polarized power cord plug (one blade is wider
than the other), or a three-wire grounding type plug.

POLARIZED PLUG CAUTION:
This plug will only fit into an outlet one way. If you cannot
fully insert the plug, try reversing it. If it still will not fit,
have an electrician install the proper wall outlet. Do not
defeat the safety feature by tampering with the plug.
GROUNDING PLUG CAUTION:
This plug will only fit into a three-hole grounding outlet.
If necessary, have an electrician install the proper outlet.
Do not defeat the safety feature by tampering with the plug.
3 POWER CORD

Make sure power cords are routed so that they are not
likely to have anything rest on them, roll over them, or
be in the way of walking traffic. If an extension cord is
used, make sure it also has either a polarized or
grounded plug and that the cords can be securely
connected. Frayed cords, damaged plugs, and damaged
or cracked wire insulation are hazardous and should be
replaced by a qualified service technician.
Overloaded outlets and extension cords are fire hazards
and should be avoided.

Ventilation openings in the cabinet release heat
generated during operation. If they are blocked, heat
build-up inside the unit can cause failures that may
result in a fire hazard or heat damage to cassettes.
For protection, follow these rules:
a. Never cover ventilation slots or the unit while in use,

or operate the unit when placed on a bed, sofa, rug,
or other soft surface.

b. Avoid built-in installation, such as a book case or

rack, unless proper ventilation is provided.

TEMPERATURE CHANGES
Do not place the unit over or near any kind of heater or
radiator, in direct sunlight, inside a closed vehicle, etc..
Do not move the unit suddenly between areas of
extreme temperature variation. If the unit is suddenly
moved from a cold place to a warm place, moisture may
condense in the unit and on the tape.

• Do not place unsecured equipment on a

sloping surface.

• Do not place this unit on any support

that is not firm, level, and adequately
strong. The unit could fall causing
serious injury to a child or adult and
damage to the unit.

• An appliance and cart combination should be moved

with care. Quick stops, excessive force, and uneven
surfaces may cause the appliance and cart
combination to overturn.

• Carefully follow all operating instructions and use the

manufacturer's recommended accessories when
operating this unit or connecting it to any other
equipment.

If the unit has been in storage or moved to a new location, refer
first to the INSTALLATION section of these safeguards.
1

IF EQUIPMENT IS EXPOSED TO RAIN,  MOISTURE, OR
STRONG IMPACT, unplug the unit and have it inspected by
a qualified service technician before use.

DURING AN ELECTRICAL STORM
During a lightning storm, whether indoors or outdoors, or
before leaving the unit unused for extended periods of time,
disconnect all equipment from the power source as well as
the antenna and cable system.

WHEN THE UNIT IS PLUGGED IN
• Never expose the unit to rain or water. DO NOT OPERATE

if liquid has been spilled into the unit. Immediately unplug
the unit, and have it inspected by a service technician.
Fire and shock hazards can result from electrical shorts
caused by liquid contact inside.

• Never drop or push any object through openings in the

unit. Some internal parts carry hazardous voltages and
contact can cause electric shock or fire hazard.

• Avoid placing the unit directly above or below your TV set

as this may cause electrical interference.
Keep all magnets away from electronic equipment.

USING ACCESSORIES
Use only accessories recommended by the manufacturer to
avoid risk of fire, shock, or other hazards.

CLEANING THE UNIT
Unplug the unit. Then, use a clean, dry, chemically untreated cloth
to gently remove dust or debris. DO NOT USE cleaning fluids,
aerosols, or forced air that could over-spray, or seep into the unit
and cause electrical shock. Any substance such as wax,
adhesive tape, etc. may mar the cabinet surface. Exposure to
greasy, humid, or dusty areas may adversely affect internal parts.

DO NOT SERVICE THIS PRODUCT YOURSELF
If, after carefully following the detailed operating
instructions, this Video product does not operate properly,
do not attempt to open or remove covers, or make any
adjustments not described in the manual. Unplug the unit
and contact a qualified service technician.

IF REPLACEMENT PARTS ARE REQUIRED
Make sure the service technician uses only parts specified by
the manufacturer, or those having the same safety
characteristics as the original parts. The use of unauthorized
substitutes may result in fire, electric shock, or other hazards.

HAVE THE SERVICE TECHNICIAN PERFORM A SAFETY CHECK
After any service or repairs to the unit, request the service
technician to conduct a thorough safety check as described
in the manufacture’s service literature to ensure that the
video unit is in safe operating condition.

SAFE ANTENNA AND CABLE CONNECTION
If an outside antenna or cable system is connected to the
equipment, be sure the antenna or cable system is grounded
so as to provide some protection against built up static
charges and voltage surges. Part 1
of the Canadian Electrical Code, in
USA Section 810 of the National
Electrical Code, ANSI/NFPA 70,
provides information with respect to
proper grounding of the mast and
supporting structure, grounding of the
lead-in wire to an antenna discharge unit, size
of grounding conductors, location of antenna discharge unit,
connection to grounding electrodes and requirements for the
grounding electrode.

KEEP ANTENNA CLEAR OF HIGH VOLTAGE POWER LINES OR CIRCUITS
An outside antenna system should be located well away from
power lines, electric light or power circuits and where it will never
come into contact with these power sources if it should happen
to fall. When installing an outside antenna, extreme care should
be taken to avoid touching power lines, circuits or other power
sources as this could be fatal. Because of the hazards involved,
antenna installation should be left to a professional.

This symbol warns the user that uninsulated voltage within the unit may
have sufficient magnitude to cause electric shock. Therefore, it is
dangerous to make any kind of contact with any inside part of this unit.

This symbol alerts the user that important literature concerning the
operation and maintenance of this unit has been included.
Therefore, it should be read carefully in order to avoid any problems.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK)

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

Screen-right appears during
play if clogging is detected.
To remove screen, press PLAY.

cleaning cassette only.
(Part No. NV-TCL30PT is recommended.)

• Follow cleaning tape instructions carefully.

Excessive use of tape can shorten head life.

• If head clog symptoms persist, contact your

nearest Factory Servicentre or authorized
Servicentre (p. 12).

4624S-K Basic-2 (031219) new form.p65

2003/12/22, 15:24

3

LSQT0823A (E) Basic OP - Back