Panasonic KX-PS8000 Manual
28
Note for Terminator setting:
B
The terminator must be installed or set to ON
on the last SCSI device only.
on the last SCSI device only.
Make sure the computer, scanner and
the other connected peripheral
devices are turned off.
the other connected peripheral
devices are turned off.
Connect the SCSI cable to the
computer’s SCSI connector and to the
scanner’s SCSI connector A or B.
computer’s SCSI connector and to the
scanner’s SCSI connector A or B.
B
The SCSI-2 board must be installed in the
computer.
If you do not have a SCSI-2 board or a
SCSI interface cable, you will need to
purchase one from your local computer
store or dealer (
computer.
If you do not have a SCSI-2 board or a
SCSI interface cable, you will need to
purchase one from your local computer
store or dealer (
☞
P. 11).
B
If other SCSI devices are connected to the
computer, connect the scanner anywhere in
the SCSI chain.
computer, connect the scanner anywhere in
the SCSI chain.
Make sure the SCSI ID No. of the
scanner is 2 (default setting).
scanner is 2 (default setting).
B
If other devices are connected to the
computer, make sure that each SCSI device
has a different ID No.
computer, make sure that each SCSI device
has a different ID No.
B
To change the scanner’s ID No., use the ID
No. switches (#1, #2, #3) located on the
back of the scanner. Also refer to Table 1
on page 29.
No. switches (#1, #2, #3) located on the
back of the scanner. Also refer to Table 1
on page 29.
If the scanner is the last device, set its
terminator switch (#4) to ON. Go to
step 5.
terminator switch (#4) to ON. Go to
step 5.
If the scanner is not the last device,
make sure the terminator switch (#4)
is set to OFF (default setting).
make sure the terminator switch (#4)
is set to OFF (default setting).
Connect the power cord to the
scanner’s AC inlet and to an AC
outlet.
scanner’s AC inlet and to an AC
outlet.
Note for Terminator setting:
B
The printer must be the last device in the chain.
The terminator setting of all other devices in
the chain must be off.
The terminator setting of all other devices in
the chain must be off.
■
Using a SCSI cable:
Make sure the computer, printer and
the other connected peripheral
devices are turned off.
the other connected peripheral
devices are turned off.
Connect the SCSI cable to the
computer’s SCSI connector and the
printer’s SCSI connector.
computer’s SCSI connector and the
printer’s SCSI connector.
B
A SCSI-2 board must be installed in the
computer.
If you do not have a SCSI-2 board or a
SCSI interface cable, you will need to
purchase one from your local computer
store or dealer (
computer.
If you do not have a SCSI-2 board or a
SCSI interface cable, you will need to
purchase one from your local computer
store or dealer (
☞
P. 11).
Make sure the SCSI ID No. of the
printer is 1 (default setting).
printer is 1 (default setting).
B
If you have other devices connected to the
computer, make sure that each SCSI device
has different ID No.
computer, make sure that each SCSI device
has different ID No.
B
To change the printer’s ID No., use the ID
No. switches (#1, #2, #3) located on the
back of the printer. Also refer to Table 1 on
page 29.
No. switches (#1, #2, #3) located on the
back of the printer. Also refer to Table 1 on
page 29.
Make sure the terminator switch (#4)
of the printer is set to ON (default
setting).
of the printer is set to ON (default
setting).
Connect the power cord to the
printer’s AC inlet and to an AC outlet.
printer’s AC inlet and to an AC outlet.
1
2
3
4
5
Connecting the Printer to a
Computer
Computer
12
3
4
ON
Setup
Connecting
the
System
(Connecting
the
Scanner/Printer
to
a
a
Computer)
Connecting the Scanner to
a Computer
a Computer
1
2
3
4
A
5
4
B
1
2
3
4
ON