Panasonic KX-MB2575 Operating Guide
10.1.2 Fax features y
Feature
Code
Selection
TEL/FAX delayed
ring count
ring count
#212
If you use an extension telephone in TEL/FAX mode, select the desired number
of times the extension telephone rings before the unit answers the call.
M1N “1”
M2N “2” (default)
M3N “3”
M4N “4”
M5N “5”
M6N “6”
M7N “7”
M8N “8”
M9N “9”
of times the extension telephone rings before the unit answers the call.
M1N “1”
M2N “2” (default)
M3N “3”
M4N “4”
M5N “5”
M6N “6”
M7N “7”
M8N “8”
M9N “9”
Note:
R See page 65 for details.
R The selection may vary depending on the location setting (feature #114 on
R See page 65 for details.
R The selection may vary depending on the location setting (feature #114 on
R If you change the location setting (feature #114 on page 73), the TEL/FAX
delayed ring count will be reset to “2”. If necessary, select the desired ring
count again.
count again.
Turning the AUTO
ANSWER
ANSWER
#319
This feature is only available when “GERMANY” is selected in feature #114 on
page 73.
M0N “OFF”
M1N “ON” (default)
page 73.
M0N “OFF”
M1N “ON” (default)
Note:
R See page 65 for details.
R See page 65 for details.
Sending report
#401
To print a sending report.
M0N “OFF”: Sending reports will not be printed.
M1N “ON”: A sending report will be printed after every fax transmission.
M2N “ERROR” (default): A sending report will be printed only when fax transmission
fails.
M0N “OFF”: Sending reports will not be printed.
M1N “ON”: A sending report will be printed after every fax transmission.
M2N “ERROR” (default): A sending report will be printed only when fax transmission
fails.
Automatic journal
report
report
#402
When “ON” is selected, the unit will print a journal report automatically after every
30 new fax transmissions and receptions (page 62).
M0N “OFF”
M1N “ON” (default)
30 new fax transmissions and receptions (page 62).
M0N “OFF”
M1N “ON” (default)
Manual answer
mode
mode
#404
To change the receiving mode in the manual answer setting (page 65).
M1N “TEL” (default)
M2N “TEL/FAX”
M1N “TEL” (default)
M2N “TEL/FAX”
Default fax
resolution
resolution
#405
To change the default resolution setting for fax.
M1N “STANDARD” (default): For normal-sized characters.
M2N “FINE”: For small-sized characters.
M3N “SUPER FINE”: For very small-sized characters.
M4N “PHOTO”: For photographs, shaded drawings, etc.
M1N “STANDARD” (default): For normal-sized characters.
M2N “FINE”: For small-sized characters.
M3N “SUPER FINE”: For very small-sized characters.
M4N “PHOTO”: For photographs, shaded drawings, etc.
Note:
R Using the “FINE”, “SUPER FINE” and “PHOTO” settings will increase
R Using the “FINE”, “SUPER FINE” and “PHOTO” settings will increase
transmission time.
Duplex print
setting for fax
reception
setting for fax
reception
#407
To set the duplex print for fax reception.
M0N “OFF” (default)
M1N “LONG EDGE”
M2N “SHORT EDGE”
M0N “OFF” (default)
M1N “LONG EDGE”
M2N “SHORT EDGE”
80
10. Programmable Features