Panasonic KXTGC224E Operating Guide
5
MbN: “Yes” a MOKN a M
N
Other programming
Changing the handset name
Each handset can be given a customised
name (“Bob”, “Kitchen”, etc.). This is useful
when you make intercom calls between
handsets. You can also select whether or not
the handset name is displayed in standby
mode. The default setting is “No”. If you select
“Yes” without entering any handset name,
“Handset 1” to “Handset 4” is displayed.
name (“Bob”, “Kitchen”, etc.). This is useful
when you make intercom calls between
handsets. You can also select whether or not
the handset name is displayed in standby
mode. The default setting is “No”. If you select
“Yes” without entering any handset name,
“Handset 1” to “Handset 4” is displayed.
1
M
N#104
2
Enter the desired name (10 characters
max.).
max.).
3
MOKN
4
MbN: Select the desired setting. a MOKN
2 times a M
2 times a M
N
Call restriction
You can restrict selected handsets from
dialling certain numbers. You can assign up to
6 phone numbers to be restricted, and select
which handsets are to be restricted. Storing
area codes here prevents the restricted
handsets from dialling any phone number in
that area code.
dialling certain numbers. You can assign up to
6 phone numbers to be restricted, and select
which handsets are to be restricted. Storing
area codes here prevents the restricted
handsets from dialling any phone number in
that area code.
1
M
N#256
2
Enter the base unit PIN (default: “0000”).
R If you forget your PIN, see page 39.
R If you forget your PIN, see page 39.
3
Select the handsets to be restricted by
pressing 1 to 4.
R All handsets registered to the base unit
pressing 1 to 4.
R All handsets registered to the base unit
are displayed.
R “ ” is displayed next to the selected
handset numbers.
R To cancel a selected handset, press
the same dial key again. “ ”
disappears.
disappears.
4
MOKN
5
Select a memory location by pressing 1
to 6. a MOKN
to 6. a MOKN
6
Enter the phone number or area code to
be restricted (8 digits max.). a MOKN a
M
be restricted (8 digits max.). a MOKN a
M
N
Changing the base unit PIN
Important:
R If you change the PIN (Personal
R If you change the PIN (Personal
Identification Number), please make note of
your new PIN. The unit will not reveal the
PIN to you. If you forget your PIN, see
page 39.
your new PIN. The unit will not reveal the
PIN to you. If you forget your PIN, see
page 39.
1
M
N#132
2
Enter the current 4-digit base unit PIN
(default: “0000”).
(default: “0000”).
3
Enter the new 4-digit base unit PIN. a
MOKN
MOKN
4
MbN: “Yes” a MOKN a M
N
Increasing the range of the base
unit
unit
You can increase the signal range of the base
unit by using a DECT repeater. Please use
only the Panasonic DECT repeater noted on
page 4. Contact your Panasonic dealer for
details.
Important:
R Before registering the repeater to this base
unit by using a DECT repeater. Please use
only the Panasonic DECT repeater noted on
page 4. Contact your Panasonic dealer for
details.
Important:
R Before registering the repeater to this base
unit, you must turn the repeater mode on.
R Do not use more than one repeater at a
time.
Setting the repeater mode
1
M
N#138
2
MbN: Select the desired setting. a MOKN
a M
a M
N
Registering the DECT repeater
(KX-A405) to the base unit
(KX-A405) to the base unit
Note:
R Please use a repeater that has not yet been
R Please use a repeater that has not yet been
registered to another unit. If the repeater is
registered to another unit, deregister it first,
registered to another unit, deregister it first,
Helpline Tel. No.: U.K. 0844 844 3899 Ireland 01289 8333
27
Programming
TGC21x_22xE_OI_(en-en)_0402_ver.110.pdf 27
2014/04/02 19:29:46