Panasonic KX-PRW110FX Operating Guide
Baby monitor sensitivity
You can adjust the sensitivity of the baby
monitor. Increase or decrease the sensitivity to
adjust the sound level needed to trigger the
baby monitor feature.
R This feature cannot be set during a
monitor. Increase or decrease the sensitivity to
adjust the sound level needed to trigger the
baby monitor feature.
R This feature cannot be set during a
monitoring call.
1
Press MMenuN on the handset being
monitored.
monitored.
2
MbN: “Sensitivity Level” a MOKN
3
MbN: Select the desired setting. a MOKN
a M
a M
N
Answering the baby monitor
n
When monitoring with a handset:
Press M
Press M
N to answer calls.
If you want to respond from the monitoring
handset, press M
handset, press M
N.
R The monitoring handset will answer calls
automatically when the auto intercom
feature is set to “On” (page 17).
feature is set to “On” (page 17).
Note:
R If you receive an outside call when
R If you receive an outside call when
communicating with the monitored
handset, you hear 2 tones. To answer
the call, press M
handset, you hear 2 tones. To answer
the call, press M
N, then press M
N.
n
When monitoring from an outside line:
To answer a call, follow the operation for
your phone.
If you want to respond from the monitoring
handset, press #1 using tone dialling.
You can turn off the baby monitor feature
by pressing #0.
Note:
R 2 minutes after the monitored handset
To answer a call, follow the operation for
your phone.
If you want to respond from the monitoring
handset, press #1 using tone dialling.
You can turn off the baby monitor feature
by pressing #0.
Note:
R 2 minutes after the monitored handset
starts a call, communication between the
monitored handset and monitoring
phone line is turned off automatically.
monitored handset and monitoring
phone line is turned off automatically.
Other programming
Changing the handset name
Each handset can be given a customised
name (“Bob”, “Kitchen”, etc.). This is useful
when you make intercom calls between
handsets. You can also select whether or not
the handset name is displayed in standby
mode. The default setting is “No”. If you select
“Yes” without entering any handset name,
“Handset 1” to “Handset 6” is displayed.
name (“Bob”, “Kitchen”, etc.). This is useful
when you make intercom calls between
handsets. You can also select whether or not
the handset name is displayed in standby
mode. The default setting is “No”. If you select
“Yes” without entering any handset name,
“Handset 1” to “Handset 6” is displayed.
1
MMenuN (right soft key) #104
2
Enter the desired name (max. 10
characters).
characters).
3
MOKN
4
MbN: Select the desired setting. a MOKN
2 times a M
2 times a M
N
Call restriction
You can restrict selected handsets from
dialling certain numbers. You can assign up to
6 phone numbers to be restricted, and select
which handsets are to be restricted. Storing
area codes here prevents the restricted
handsets from dialling any phone number in
that area code.
dialling certain numbers. You can assign up to
6 phone numbers to be restricted, and select
which handsets are to be restricted. Storing
area codes here prevents the restricted
handsets from dialling any phone number in
that area code.
1
MMenuN (right soft key) #256
2
Enter the base unit PIN (default: “0000”).
R If you forget your PIN, contact an
R If you forget your PIN, contact an
authorised service centre.
3
Select the handsets to be restricted by
pressing 1 to 6.
R All handsets registered to the base unit
pressing 1 to 6.
R All handsets registered to the base unit
are displayed.
R “ ” is displayed next to the selected
handset numbers.
R To cancel a selected handset, press
the same dial key again. “ ”
disappears.
disappears.
4
MOKN
5
Select a memory location by pressing 1
to 6. a MOKN
to 6. a MOKN
31
Programming