Panasonic SL-CT710 Operating Guide

Page of 6
Cannot change the
Digital Re-master mode,
anti-skip mode.
Cannot specify point A
or B.
Digital Re-master does
not work.
Cannot skip albums.
Cannot hear the remote
control’s operation tone.
The remote control does
not work properly.
The unit beeps rapidly.
Cannot recharge.
The AC adaptor
becomes warm during
recharging.
The batteries are taking
a long time to recharge.
Play time is short after
recharging.
The battery indicator
fails to appear or is
incorrect.
The unit stops working.
No play.
No sound or there is a
lot of noise.
Play doesn’t resume
from the last point
stopped.
Play doesn’t start from
the first track.
Cannot search through
tracks.
Before requesting service, make the below checks. If you are in doubt about some of the check points, or if the remedies indicated in the chart do not solve the problem,
consult your dealer for instructions. (The information in Italics applies only to areas other than Europe, Australia and N.Z.)
Troubleshooting guide
1
Dear Customer
Thank you for purchasing this product.
Before connecting, operating or adjusting
this product, please read these instructions
completely. Please keep this manual for
future reference.
Matsushita Electric Industrial Co., Ltd.
Web Site: http://www.panasonic.co.jp/global/
GN GK GH GC GS
EB
EG
Note:
≥ 
“EB” on the packaging indicates the
United Kingdom.
≥ 
Actual lid design may differ but functions
and operations are the same.
Portable CD Player
Operating Instructions
SL-CT710
RQT7192-1B
F0903KN1024
p
The HOLD function is on. Release HOLD (
➪page 5).
The batteries may have run empty (
➪page 5).
(If play is extremely short even after fully recharging the
batteries, the batteries may have exceeded their life.
Rechargeable batteries can be recharged approximately 300
times.)
The disc isn’t correctly set.
The disc is scratched or dirty. (Tracks skipped.)
There is moisture on the lens. Wait for about an hour and
then try again.
The lens is dirty: clean it with a blower (recommended
product: SZZP1038C).If the lens gets marked with
fingerprints, gently wipe them off with a cotton swab.
The unit may not read MP3 correctly if it is shaken while it is
reading the files.
Play of a multi-session disc may not be possible if there is a
blank data segment between sessions.
If there is large JPEG data etc. within a MP3 file, sound may
become muted and play may not possible. 
If you try playing a CD that contains CD-ROM format data and
normal audio data (CD-DA), output from one of the above
may become silent, and play may not be possible.
Ensure the plugs are inserted firmly.
Wipe the plugs clean with a clean cloth.
Noise may occur when playing MP3 if recording quality is
poor.
The elapsed playing time disappears and sound is interrupted
if bumps continue repeatedly.
There is no sound from the earphones if you have connected
the unit to other equipment.
This doesn’t work if you change discs.
This doesn’t work during random play. 
It may not work correctly under some conditions.
Random play modes may be on (
➪page 6).
Play resumes from the last point stopped.
You cannot search through MP3 files.
If [:] or [9] is pressed before [$MEMO/%DISP] you
cannot change the mode.
You may not be able to specify point A or B at the end of disc.
Depending on the type of MP3 disc recording, the effect may
not appear.
You cannot skip between the first and last albums during play.
The operation tone may be off (
➪page 6).
Use only the included remote control to operate this unit.
The operation is not possible. You cannot adjust the volume,
sound quality or anti-skip system if you have connected the
unit to other equipment. Adjust them on the other equipment.
You aren’t using the special rechargeable batteries.
You must insert two batteries before you can recharge them.
The unit must be off before you can recharge.
This is normal.
The batteries may take a maximum of 6 hours to recharge
under some conditions.
This may occur after the first time you recharge the batteries
or haven’t used them for a long time. Play time should be
restored after a few recharges.
The batteries can go flat if you leave the AC adaptor
connected after recharging is complete.
The indicator does not appear when the AC adaptor is
connected.
The indicator does not appear correctly when using the
rechargeable and dry cell batteries at the same time and
under certain conditions.
Disconnect then reconnect all power sources (batteries and
AC adaptor).
SG
RQT7192-1B.qxd  04.2.10 11:29 AM  ページ 1