Panasonic TH-50PV60E Operating Guide
FAQs, etc.
30
31
Licence
Trademark Credits
•
VGA is a trademark of International Business Machines Corporation.
•
Macintosh is a registered trademark of Apple Computer, USA.
•
S-VGA is a registered trademark of the Video Electronics Standard Association.
Even if no special notation has been made of company or product trademarks, these trademarks have been fully
respected.
•
HDMI, the HDMI Logo and High-Defi nition Multimedia Interface are trademarks or registered trademarks of
HDMI Licensing LLC.
•
HDAVI Control
TM
is a trademark of Matsushita Electric Industrial Co., Ltd.
Problem
Actions
Screen
FAQs
Sound
Other
HDMI
Specifi cations
Note
•
Design and Specifi cations are subject to change without notice. Weight and Dimensions shown are approximate.
•
This equipment complies with the EMC standards listed below.
EN55013, EN61000-3-2, EN61000-3-3, EN55020, EN55022, EN55024.
TH-50PV60E
Power Source
AC 220-240 V, 50 / 60 Hz
Power
Consumption
Average use
368 W
Standby condition
0.3 W
Plasma
Display panel
Drive method
AC type
Aspect Ratio
16:9
Contrast Ratio
Max 10000:1
Visible screen size
(No. of pixels)
127 cmV
1,106 mm (W) × 622 mm (H) × 1,269 mm (diagonal)
1,049,088 (1,366 (W) × 768 (H)) [4,098 × 768 dots]
1,106 mm (W) × 622 mm (H) × 1,269 mm (diagonal)
1,049,088 (1,366 (W) × 768 (H)) [4,098 × 768 dots]
Sound
Speaker
12 cm × 6 cm × 2 pcs, 8 Ω
Audio Output
20 W (10 W + 10 W ), 10% THD
Headphones
M3 (3.5 mm) Jack × 1
PC signals
VGA, SVGA, XGA
SXGA ······ (compressed)
Horizontal scanning frequency 31 - 69 kHz
Vertical scanning frequency 59 - 86 Hz
Receiving Systems /
Band name
PAL B, G, H, I, SECAM B, G, SECAM L / L’
VHF E2 - E12
VHF H1 - H2 (ITALY)
VHF A - H (ITALY)
UHF E21 - E69
CATV (S01 - S05)
CATV S1 - S10 (M1 - M10)
CATV S11 - S20 (U1 - U10)
CATV S21 - S41 (Hyperband)
PAL D, K, SECAM D, K
VHF R1 - R2
VHF R3 - R5
VHF R6 - R12
UHF E21 - E69
PAL 525/60
Playback of NTSC tape from some PAL Video re cord ers (VCR)
M.NTSC
Playback from M. NTSC Video recorders (VCR)
NTSC (AV input only) Playback from NTSC Video recorders (VCR)
Aerial - Rear
VHF / UHF
Operating Conditions
Temperature : 0 °C - 40 °C
Humidity
: 20 % - 80 % RH (non-condensing)
Connection T
erminals
AV1 (Scart terminal)
21 Pin terminal (Audio/Video in, Audio/Video out, RGB in)
AV2 (Scart terminal)
21 Pin terminal (Audio/Video in, Audio/Video out, S-Video in, Q-Link)
AV3 (Scart terminal)
21 Pin terminal (Audio/Video in, Audio/Video out, RGB in, S-Video in, Q-Link)
AV4
VIDEO
RCA PIN Type × 1
1.0 V[p-p] (75 Ω)
S-VIDEO
Mini DIN 4-pin
Y:1.0 V[p-p] (75 Ω) C:0.286 V[p-p] (75 Ω)
AUDIO L - R
RCA PIN Type × 2
0.5 V[rms]
Others
COMPONENT Y
1.0 V[p-p] (including synchronization)
P
B
, P
R
±0.35
V[p-p]
HDMI1/2
TYPE A Connectors
PC
HIGH-DENSITY D-SUB 15PIN
R,G,B/0.7 V[p-p] (75 Ω)
HD, VD/TTL Level 2.0 - 5.0 V[p-p] (high impedance)
AUDIO L - R
RCA PIN Type × 2
0.5 V[rms]
Output AUDIO L - R
RCA PIN Type × 2
0.5 V[rms] (high impedance)
Dimensions ( W × H × D )
1,210 mm × 818 mm × 95 mm
Weight
40.0 k Net
No image can be
displayed
displayed
•
Is "Colour" or "Contrast" in the Picture menu set to the
minimum? (p. 14)
Blurry or
distorted image
distorted image
(no sound or low volume)
•
Reset channels. (p. 18)
Neither image nor
sound is produced
sound is produced
•
Is the unit in "AV mode"?
•
Is the mains lead plugged into the socket outlet?
•
Is the TV unit turned On?
•
Check Picture menu (p. 14) and volume.
No sound is produced
•
Is "Sound Mute" active? (p. 7)
•
Is the volume set to the minimum?
Sound level is low
or sound is distorted
or sound is distorted
•
Sound signal reception may be deteriorated.
•
Set "MPX" (p. 14) in the Sound menu to "Mono".
Sound is unusual
•
Set the sound setting of the connected equipment
to "2ch L.PCM".
•
Check the "HDMI1 input" setting in the Sound menu.
(p. 14)
•
If digital sound connection has a problem, select
analogue sound connection. (p. 27)
An error message
appears
appears
•
Contact the authorized Service Centre.
TV unit goes into
"Standby mode"
"Standby mode"
•
The sleep function is activated.
•
The TV unit enters "Standby mode" about 30 min.
after broadcasting ends.
An error message
appears
appears
•
Follow the message's instructions.
•
If the problem persists, contact the authorized
Service Centre.
Chaotic image, noisy
•
Set "P-NR" in the Picture menu (to remove noise).
(p. 14)
•
Check nearby electrical products
(car, motorcycle, fl uorescent lamp).
•
Licence / Speci
fi cations
•
Frequently Asked
Questions
"Control with HDMI"
function does not work
function does not work
•
Switch the TV unit on again with the equipment on.
•
Set "Control with HDMI" to "Off", then set to "On" again.
(p. 21)
Whirling sound is
heard
heard
•
The sound is from built-in cooling fan (not a sign of faulty
operation).