Toshiba 24" Toshiba HD Ready TV Important Safety Instructions

English   - 11 -

Connect the power cord to a power source such as a 

wall socket (220-240V AC, 50 Hz). 
To switch on the TV from standby mode either:
•  Press the 

Standby button, Programme +/- or a 

numeric button on the remote control.

•  Press the side function switch on the TV until the TV 

comes on from standby.

Press the 

Standby button on the remote control or 

press the side function switch on the TV until the TV 

switches into standby mode.
To power down the TV completely, unplug the 

power cord from the mains socket.
Note: When the TV is switched into standby mode, the 

When turned on for the first time, the language 

selection screen is displayed. Select the desired 

language and press 

OK.

On the next screen, set your preferences using the 

directional buttons.
Note: Depending on the Country selection you may be 

Digital Aerial: If Digital Aerial broadcast search 

option is turned on, the TV will search for digital 

terrestrial broadcasts after other initial settings are 

completed.
Digital Cable: If Digital Cable broadcast search 

option is turned on, the TV will search for digital cable 

broadcasts after other initial settings are completed. 

According  to  your  other  preferences  a  confirmation 

message may be displayed before starting to search. 

Select 

YES and press OK to proceed. To cancel 

operation, select 

NO and press OK. You can select 

Network or set values such as Frequency, Network 

ID and Search Step. When finished, press OK button. 

Satellite(**): If Satellite broadcast search option 

is turned on, the TV will search for digital satellite 

broadcasts after other initial settings are completed. 

Before satellite search is performed some settings 

should be made. 

Antenna Type menu will be displayed 

first. You can select 

Antenna Type as Direct, Single 

Satellite Cable or DiSEqC switch by using “ ” or “

” buttons.

•  Direct: If you have a single receiver and a direct satellite 

dish, select this antenna type. Press 

OK to continue. 

Select an available satellite on the next screen and 

press 

OK to scan for services. 

•  Single Satellite Cable: If you have multiple 

receivers and a single satellite cable system, select 

this antenna type. Press 

OK to continue. Configure 

settings by following instructions on the next screen. 

Press 

OK to scan for services.

•  DiSEqC switch: If you have multiple satellite dishes 

and a 

DiSEqC switch, select this antenna type. 

Press 

OK to continue. You can set four DiSEqC 

options (if available) on the next screen. Press 

OK 

button to scan the first satellite in the list.

Analogue:  If Analogue broadcast search option is 

turned on, the TV will search for analogue broadcasts 

after other initial settings are completed.
Additionally you can set a broadcast type as your 

favourite one. Priority will be given to the selected 

broadcast type during the search process and the 

channels of it will be listed on the top of the 

List. When finished, press OK to continue.
You can activate 

Store Mode option at this point. 

This option will configure your TV’s settings for store 

environment and depending on the TV model being 

used, the supported features of it may be displayed 

on the top of the screen as an info banner. This option 

is intended only for store use. It is recommended to 

select 

Home Mode for home use. This option will be 

available in 

System>Settings>More menu and can 

be turned off/on later. 
Press 

OK button on the remote control to continue.

After the initial settings are completed TV will start 

to search for available broadcasts of the selected 

broadcast types.
After all the available stations are stored, scan results 

will be displayed. Press 

OK to continue. The Edit 

Channel List menu will be displayed next. You can 

edit the channel list according to your preferences or 

press the 

Menu button to quit and watch TV.

While the search continues a message may appear, 

asking whether you want to sort channels according 

to the LCN

(*). Select Yes and press OK to confirm.