Moxa IMC-P101-M-SC Media Converter Specification Guide
Ethernet Media Converters and Extenders
1
w w w. m o x a . c o m
IEEE 802.3af PoE Ethernet-to-fiber media converters
Introduction
Specifications
IMC-P101 series Ethernet-to-fiber media converters provide Ethernet
media conversion from 10/100BaseT(X) to 100BaseFX (with SC or
ST connectors). These converters are classified as power source
equipment (PSE), and when used in this way provide up to 15.4
watts to IEEE 802.3af compliant powered devices (PDs), eliminating
media conversion from 10/100BaseT(X) to 100BaseFX (with SC or
ST connectors). These converters are classified as power source
equipment (PSE), and when used in this way provide up to 15.4
watts to IEEE 802.3af compliant powered devices (PDs), eliminating
the need for additional wiring. The IMC-P101 converters support
IEEE 802.3/802.3u/802.3x with 10/100M, full/half-duplex, and MDI/
MDI-X auto-sensing, providing a complete solution for your industrial
Ethernet network.
IEEE 802.3/802.3u/802.3x with 10/100M, full/half-duplex, and MDI/
MDI-X auto-sensing, providing a complete solution for your industrial
Ethernet network.
Power over Ethernet
IMC-P101 Series
›
10/100BaseT(X) auto-negotiation and auto-MDI/MDI-X
›
IEEE 802.3af compliant PoE PSE equipment
›
Power failure alarm by relay output
›
Store-and-forward mode and pass through mode
›
-40 to 75°C operating temperature range (T models)
›
Redundant dual DC power inputs
Technology
Standards:
IEEE 802.3 for 10BaseT
IEEE 802.3u for 100BaseT(X), 100BaseFX
IEEE 802.3af for Power-over-Ethernet
IEEE 802.3 for 10BaseT
IEEE 802.3u for 100BaseT(X), 100BaseFX
IEEE 802.3af for Power-over-Ethernet
Interface
RJ45 Ports: 10/100BaseT(X)
Fiber Ports: 100BaseFX (SC/ST connectors)
LED Indicators: PWR1, PWR2, Fiber Link, 10/100M (TP port), PSE
Indicator
DIP Switches:
Fiber Ports: 100BaseFX (SC/ST connectors)
LED Indicators: PWR1, PWR2, Fiber Link, 10/100M (TP port), PSE
Indicator
DIP Switches:
DIP No.
Function
ON
OFF
1
Auto Negotiation
Enable*
Disable
2
Force TP Speed
100 Mbps*
10 Mbps
3
Force TP Duplex
Full Duplex*
Half Duplex
4
Link Fault Pass
Through
Enable*
Disable
5
Operating Mode
Store-and-Forward*
Pass Through
6
PSE
Disable
Enable*
7
P.R.R.
(PD Remote Reset)
Enable
Disable*
* Default DIP switch setting.
Alarm Contact: One relay output with current carrying capacity of 1 A
@ 24 VDC
@ 24 VDC
Optical Fiber
100BaseFX
Multi-Mode
Single-Mode
Fiber Cable Type
OM1
50/125 μm
G.652
800 MHz*km
Typical Distance
4 km
5 km
40 km
Wave-
length
Typical (nm)
1300
1310
TX Range (nm)
1260 to 1360
1280 to 1340
RX Range (nm)
1100 to 1600
1100 to 1600
Optical
Power
TX Range (dBm)
-10 to -20
0 to -5
RX Range (dBm)
-3 to -32
-3 to -34
Link Budget (dB)
12
29
Dispersion Penalty (dB)
3
1
Note: When connecting a single-mode fiber transceiver, we recommend
using an attenuator to prevent damage caused by excessive optical power.
Note: Compute the “typical distance” of a specific fiber transceiver as
follows: Link budget (dB) > dispersion penalty (dB) + total link loss (dB).
Physical Characteristics
Housing: Metal
Dimensions: 144.45 x 122.3 x 51.65 mm (5.69 x 4.81 x 2.03 in)
Weight:
Product only: 525 g (1.16 lb)
Packaged: 710 g (1.56 lb)
Installation: DIN-rail mounting, wall mounting (with optional kit)
Dimensions: 144.45 x 122.3 x 51.65 mm (5.69 x 4.81 x 2.03 in)
Weight:
Product only: 525 g (1.16 lb)
Packaged: 710 g (1.56 lb)
Installation: DIN-rail mounting, wall mounting (with optional kit)
Environmental Limits
Operating Temperature:
Standard Models: 0 to 60°C (32 to 140°F)
Wide Temp. Models: -40 to 75°C (-40 to 167°F)
Storage Temperature: -40 to 85°C (-40 to 185°F)
Ambient Relative Humidity: 5 to 95% (non-condensing)
Standard Models: 0 to 60°C (32 to 140°F)
Wide Temp. Models: -40 to 75°C (-40 to 167°F)
Storage Temperature: -40 to 85°C (-40 to 185°F)
Ambient Relative Humidity: 5 to 95% (non-condensing)