Moxa ioLogik E2260 Specification Guide
1
w w w. m o x a . c o m
i n f o @ m o x a . c o m
Industrial I/O
Active Ethernet I/O with 6 RTD inputs and 4 digital outputs
ioLogik E2260
Supports PT, JPT, Ni RTD sensor types and resistors
›
Adjustable RTD sampling rate
›
Instant event messaging by TCP/UDP/email/SNMP-trap
›
PC-based configuration utility and web console
›
Easy-to-use Click&Go™ Logic for local output control
›
Windows/WinCE VB/VC.NET and Linux C APIs
›
I/O control over Modbus/TCP and SNMP protocol
›
NIST traceable calibration
›
Specifications
Introduction
Bring Intelligence to Temperature Measurement
The ioLogik E2260 brings intelligence to temperature sensors. It
comes equipped with virtual channels that are designed to calculate
the average value of each channel and the difference between two
channels. And it does all this without a controller or PC.
comes equipped with virtual channels that are designed to calculate
the average value of each channel and the difference between two
channels. And it does all this without a controller or PC.
Compatible with Popular RTD Temperature Sensors
The ioLogik E2260 offers PT100, PT1000, JPT, and Ni sensor types
and a resistor of up to 2.2 kilo-ohms, and supports using your
own resistance sensor, such as PTC or NTC types for your HVAC
applications.
and a resistor of up to 2.2 kilo-ohms, and supports using your
own resistance sensor, such as PTC or NTC types for your HVAC
applications.
LAN
Ethernet: 1 x 10/100 Mbps, RJ45
Protection: 1.5 KV magnetic isolation
Protocols: Modbus/TCP, TCP/IP, UDP, DHCP, Bootp, SNMP (MIB for
I/O and Network), HTTP, CGI, SNTP
Protection: 1.5 KV magnetic isolation
Protocols: Modbus/TCP, TCP/IP, UDP, DHCP, Bootp, SNMP (MIB for
I/O and Network), HTTP, CGI, SNTP
Serial Communication
Interface: RS-485-2w: Data+, Data-, GND
Serial Line Protection: 15 KV ESD for all signals
Serial Line Protection: 15 KV ESD for all signals
Serial Communication Parameters
Parity: None
Data Bits: 8
Stop Bits: 1
Flow Control: None
Baudrate: 1200 to 115200 bps
Protocol: Modbus/RTU
Data Bits: 8
Stop Bits: 1
Flow Control: None
Baudrate: 1200 to 115200 bps
Protocol: Modbus/RTU
RTD
Channels: 6
Input Type: Pt, JPt, Ni, RTD sensor, resistor
Sampling Rate: 12 samples/sec (all channels)
Resolution: 0.1°C or 0.1 ohm
Accuracy:
±0.1% FSR @ 25°C
±0.3% FSR @ -10 and 60°C
Input Impedance: 625K ohms (min.)
Input Type: Pt, JPt, Ni, RTD sensor, resistor
Sampling Rate: 12 samples/sec (all channels)
Resolution: 0.1°C or 0.1 ohm
Accuracy:
±0.1% FSR @ 25°C
±0.3% FSR @ -10 and 60°C
Input Impedance: 625K ohms (min.)
Digital Output
Channels: 4, sink, 36 VDC, 200 mA
I/O Mode: DO or Pulse Output
Pulse Wave Width/Frequency: 10 ms/100 Hz
Over-voltage Protection: 45 VDC
Over-current Limit: 750 mA
Over-temperature Shutdown: 175°C
Isolation: 3K VDC or 2K Vrms
I/O Mode: DO or Pulse Output
Pulse Wave Width/Frequency: 10 ms/100 Hz
Over-voltage Protection: 45 VDC
Over-current Limit: 750 mA
Over-temperature Shutdown: 175°C
Isolation: 3K VDC or 2K Vrms
Power Requirements
Power Input: 24 VDC nominal, 12 to 48 VDC
Power Consumption: 282 mA typical @ 24 VDC
Power Consumption: 282 mA typical @ 24 VDC
Physical Characteristics
Wiring: I/O cable max. 14AWG
Dimensions: 115 x 79 x 45.63 mm (4.53 x 3.11 x 1.8 in)
Weight: 215 g
Dimensions: 115 x 79 x 45.63 mm (4.53 x 3.11 x 1.8 in)
Weight: 215 g
Environmental Limits
Operating Temperature: -10 to 60°C (14 to 140°F)
Storage Temperature: -40 to 85°C (-40 to 185°F)
Ambient Relative Humidity: 5 to 95% (non-condensing)
Storage Temperature: -40 to 85°C (-40 to 185°F)
Ambient Relative Humidity: 5 to 95% (non-condensing)