Alpine INE-W960HDMI Owner's Manual
37
-EN
You can set your favorite BASS ENGINE type.
Setting contents: Standard (Initial setting) / Punch / Rich / Mid
Bass / Low Bass
• The function is disabled when BASS ENGINE SQ is set to “Off.”
You can adjust the BASS ENGINE Level.
Setting item: Level
Setting contents: 0 to 6 (Initial setting: 3)
Setting contents: 0 to 6 (Initial setting: 3)
• The function is disabled when BASS ENGINE SQ is set to “Off.”
• The Level 0 of the BASS ENGINE SQ is common to all the types.
• The Level 0 of the BASS ENGINE SQ is common to all the types.
About Setup when the external power amplifier is
connected
connected
In order to optimize the BASS ENGINE SQ, we recommend the
following procedure to set up the power amplifier.
After setting up, the BASS ENGINE Level will be adjusted according to
the music.
following procedure to set up the power amplifier.
After setting up, the BASS ENGINE Level will be adjusted according to
the music.
1)
Set GAIN of the power amplifier to “MIN.”
2)
Set the Crossover Mode Sector switch to “OFF.”
• If the switch has no “OFF” position, set as near as possible to
full range.
3)
Set the BASS ENGINE SQ of this unit to “ON,” and the
BASS ENGINE Level to “3.”
BASS ENGINE Level to “3.”
4)
Play a song of the genre you frequently listen to, and
adjust GAIN of the power amplifier.
adjust GAIN of the power amplifier.
1
Touch [Fader/Balance].
The Fader/Balance setting screen is displayed.
2
Touch the desired point within the image area. Or
touch [
touch [
] [
] [
] [
].
Fader: F15 to R15
Balance: L15 to R15
Balance: L15 to R15
* Touch
to return the Fader/Balance value to “00” (center).
Adjusting the Time Correction (TCR)
[TCR] is selected on the Sound setup menu in step 3. Refer to “Sound
Setup Operation” (page 34).
Before performing the following procedures, refer to “About Time
Correction” (page 40).
Setup Operation” (page 34).
Before performing the following procedures, refer to “About Time
Correction” (page 40).
Setting item: TCR (Time Correction)
1
Touch [ms] or [cm] to select mode for making
adjustments.
adjustments.
Each time you touch, the onscreen button and correction
mode changes.
mode changes.
ms: Adjust time.
cm: Adjust listening position and distance from each speaker.
cm: Adjust listening position and distance from each speaker.
2
Touch [
] or [
] for each speaker to adjust the
time or distance.
0.0msec to 9.9msec (0.1msec/step)
0.0cm to 336.6cm (3.4cm/step)
All speaker setting values are adjustable in the range of 15ms or
510cm.
0.0cm to 336.6cm (3.4cm/step)
All speaker setting values are adjustable in the range of 15ms or
510cm.
3
To store the adjusted setting value, touch and hold
[Preset1], [Preset2], or [Preset3] for at least 2
seconds.
[Preset1], [Preset2], or [Preset3] for at least 2
seconds.
• Touch [Flat] to set all values to 0.0.
• If the Rear Speaker setting is “Off,” the Rear Speaker setting cannot
• If the Rear Speaker setting is “Off,” the Rear Speaker setting cannot
be edited (Refer to page 39).
• If the Subwoofer setting is “Off,” the Subwoofer setting cannot be
edited (Refer to page 39).
Calling the Time Correction Value
Calling the pre-set time correction value.
Touch [Preset1], [Preset2], or [Preset3] on the time
correction screen.
correction screen.
The setting stored in the Preset will be recalled.
Setting the BASS ENGINE Type
Standard: Natural low-pitched sound located in front of front
seats.
Punch:
Punched bass sound, massive, with a feeling of
speed.
speed.
Rich:
You can feel wrapped with rich Low-pitched sound
by arranging super-low-pass, low-pass, and mid
lowpass, with sufficient balance.
by arranging super-low-pass, low-pass, and mid
lowpass, with sufficient balance.
Mid Bass: Emphasizes the presence of an upper bass.
Reproduces low-pass with a sense of speed.
Low Bass: Super-low-pass presence and a low-pitched sound
which is oriented downwards with deep feeling.
Adjusting the BASS ENGINE Level
Adjusting the Fader/Balance
*
Image area
Correction mode