Sony XAV-AX100 Owner's Manual

Page of 33
14
GB
Touch Panel Adjust
Adjusts the touch panel calibration if the 
touching position does not correspond with the 
proper item.
Camera Input
Selects the image from the rear view camera: 
[OFF], [Normal], [Reverse] (mirror image).
Steering Control
Selects the input mode for the connected remote 
control. To prevent a malfunction, be sure to 
match the input mode with the connected 
remote control before use.
Custom
Input mode for the steering wheel remote 
control (follow the procedures of [Steering 
Control Custom] to register functions on the 
connected remote control).
Preset
Input mode for the wired remote control 
excluding the steering wheel remote control.
Steering Control Custom
The steering button panel appears.
 Press and hold the button you want to assign 
to the steering wheel.
The button on the panel lights up (standby).
 Press and hold the button on the steering 
wheel you want to assign the function to.
The button on the panel will change the color 
(highlighted or encircled by an orange line).
 To register other functions, repeat steps  
and 
.
(Available only when [Steering Control] is set to 
[Custom].)
Notes
• While making settings, the connected remote control 
cannot be used even though some functions have 
already been registered. Use the buttons on the unit.
• If an error occurs while registering, all the registered 
information is cleared. Restart registration from the 
beginning.
• This function may not be available on some vehicles. 
For details on the compatibility of your vehicle, visit the 
support site on the back cover.
Bluetooth Connection
Activates the BLUETOOTH signal: [OFF], [ON], 
[Pairing] (enters into pairing standby mode).
Bluetooth Device Info
Displays the information of the device connected 
to the unit.
(Available only when [Bluetooth Connection] is 
set to [ON] and a BLUETOOTH device is 
connected to the unit.)
Bluetooth Reset
Initializes all BLUETOOTH-related settings such as 
pairing information, call history, history of 
connected BLUETOOTH devices, etc.
Rear View Camera Setting
Adjusts the length and/or position of the marker 
lines on the picture from the rear view camera by 
touching the arrow marks.
Factory Reset
Initializes all the settings to the factory settings.
Firmware Version
Updates and confirms the firmware version.
Open Source Licenses
Displays the software licenses.
Sound Settings
EXTRA BASS
Reinforces bass sound in synchronization with 
the volume level: [OFF], [1], [2].
EQ10/Subwoofer
Selects an equalizer curve and adjusts the 
subwoofer level.
EQ10
Selects the equalizer curve: [OFF], [R&B], [Rock], 
[Pop], [Dance], [Hip-Hop], [Electronica], [Jazz], 
[Soul], [Country], [Custom].
[Custom] adjusts the equalizer curve: –6 to +6.
Subwoofer
Adjusts the volume level of the subwoofer: 
[OFF], –10 to +10.
Balance/Fader
Adjusts the balance/fader level.
Balance
Adjusts the sound balance between the left and 
right speakers: L15 to R15.
Fader
Adjusts the sound balance between the front 
and rear speakers: Front 15 to Rear 15.
Crossover
Adjusts the cut-off frequency and subwoofer 
phase.
High Pass Filter
Selects the cut-off frequency of the front/rear 
speakers: [50Hz], [60Hz], [80Hz], [100Hz], 
[120Hz], [OFF].
Low Pass Filter
Selects the cut-off frequency of the subwoofer: 
[50Hz], [60Hz], [80Hz], [100Hz], [120Hz].
Subwoofer Phase
Selects the subwoofer phase: [Normal], 
[Reverse].
DSO (Dynamic Stage Organizer)
Enhances audio output: [OFF], [Low], [Middle], 
[High].