JVC KD-R690S Owner's Manual
22
ENGLISH
TROUBLESHOOTING
Symptom
Remedy
SiriusXM® Radio
“CH UNAVAIL”
The selected channel is unavailable. For more
information about the SiriusXM channel lineup, visit
<www.siriusxm.com>.
<www.siriusxm.com>.
“CHECK ANTENNA”
Check the antenna and its connection are in good
condition.
“CHECK TUNER”
Make sure the SiriusXM Vehicle Tuner is connected to
the unit.
“NO SIGNAL”
Make sure the antenna is mounted outside the vehicle.
“SUBSCRIPTION UPDATED
– PRESS ENTER TO
CONTINUE.”
– PRESS ENTER TO
CONTINUE.”
Your subscription is updated. Press the volume knob to
continue.
“CODE ERROR”
Make sure you have entered the correct pass code.
( 13)
“NO CONTENT”
There is insufficient content to start TuneScan.
“SCAN CANCEL”
TuneScan has been aborted.
If you have any troubles, try the following:
1
Check TROUBLESHOOTING
2
Reset the unit ( 3)
3
Contact (USA only)
Call: 1-800-252-5722 ( or ) visit: <http://www.jvc.com>
INSTALLATION/CONNECTION
Warning
• The unit can only be used with a 12 V DC power supply, negative ground.
• Disconnect the battery’s negative terminal before wiring and mounting.
• Do not connect Battery wire (yellow) and Ignition wire (red) to the car chassis or Ground wire
• Disconnect the battery’s negative terminal before wiring and mounting.
• Do not connect Battery wire (yellow) and Ignition wire (red) to the car chassis or Ground wire
(black) to prevent a short circuit.
• To prevent short circuit:
– Insulate unconnected wires with vinyl tape.
– Be sure to ground this unit to the car’s chassis again after installation.
– Secure the wires with cable clamps and wrap vinyl tape around the wires that comes into
– Insulate unconnected wires with vinyl tape.
– Be sure to ground this unit to the car’s chassis again after installation.
– Secure the wires with cable clamps and wrap vinyl tape around the wires that comes into
contact with metal parts to protect the wires.
Caution
• For safety’s sake, leave wiring and mounting to professionals. Consult the car audio dealer.
• Install this unit in the console of your vehicle. Do not touch the metal parts of this unit during
• Install this unit in the console of your vehicle. Do not touch the metal parts of this unit during
and shortly after use of the unit. Metal parts such as the heat sink and enclosure become hot.
• Do not connect the
wires of speakers to the car chassis or Ground wire (black), or connect
them in parallel.
• Connect speakers with a maximum power of more than 50 W. If the maximum power of
the speakers is lower than 50 W, change the [AMP GAIN] setting to avoid damaging the
speakers. ( 16)
speakers. ( 16)
• Mount the unit at an angle of less than 30º.
• If your vehicle wiring harness does not have the ignition terminal, connect Ignition wire (red)
• If your vehicle wiring harness does not have the ignition terminal, connect Ignition wire (red)
to the terminal on the vehicle’s fuse box which provides 12 V DC power supply and is turned
on and off by the ignition key.
on and off by the ignition key.
• Keep all cables away from heat dissipate metal parts.
• After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are
• After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are
working properly.
• If the fuse blows, first make sure the wires are not touching car’s chassis, then replace the old
fuse with one that has the same rating.
JS_JVC_KD_R690S_K_EN_3.indd 22
7/4/2017 11:01:29 AM