JL Audio Stealthbox® Owner's Manual
Stealthbox
®
I n s t a l l a t I o n G u I d e
SB-T-4RNR2/10W3v3, JL AUDIO, Inc 2010
Sheet SKU#011181 Revision 11.12.2010
Page
for the
SB-T-4RNR2/10W3v3
(‘02-Up Toyota 4-Runner SR-5, Sport
Edition & Limited)
This Stealthbox is a product which
requires professional installation skills
and tools.
Please read this installation guide thor-
oughly before beginning the project.
It will guide you step by step through
the installation. Several of the steps in
this process may require two people to
accomplish.
and tools.
Please read this installation guide thor-
oughly before beginning the project.
It will guide you step by step through
the installation. Several of the steps in
this process may require two people to
accomplish.
It is absolutely vital that the enclo-
sure be properly mounted to the
vehicle according to these instructions.
Failure to mount the enclosure properly
presents two problems: 1) The sub-
bass performance will suffer due to the
movement of the enclosure caused by
the force exerted by the woofer(s) and
2) A loose enclosure presents a serious
safety hazard in the event of a collision
or sudden deceleration.
vehicle according to these instructions.
Failure to mount the enclosure properly
presents two problems: 1) The sub-
bass performance will suffer due to the
movement of the enclosure caused by
the force exerted by the woofer(s) and
2) A loose enclosure presents a serious
safety hazard in the event of a collision
or sudden deceleration.
Please enjoy your JL Audio Stealthbox
responsibly.
STEP 1: Clean out all contents. Remove the
cargo cover and carpet mat.
cargo cover and carpet mat.
STEP 2: Remove the rear sill plate(A) and side stor-
age door(B).
With the sill plate removed, pull and fold over the
carpet out of the corner(circled).
On Limited Edition interiors, remove the plastic
tray. The flooring carpet will not fit flush aginst the
Stealthbox, once isntalled.
age door(B).
With the sill plate removed, pull and fold over the
carpet out of the corner(circled).
On Limited Edition interiors, remove the plastic
tray. The flooring carpet will not fit flush aginst the
Stealthbox, once isntalled.
STEP 3: Place the supplied wax square into
position.
The middle of wax square (X marks the
position.
The middle of wax square (X marks the
spot) needs to be 3.5” back from the wheel
well and 2.5” from the side panel.
Remove the adhesive protective paper from
the under side of the wax square and stick to
the floor.
well and 2.5” from the side panel.
Remove the adhesive protective paper from
the under side of the wax square and stick to
the floor.
STEP 4: Thread in the supplied tsocket cup set
screw, leaving about a 1/2” out of the Stealthbox.
Make sure that the socket cup end is exposed.
Place the Stealthbox into position and press down
firmly.
screw, leaving about a 1/2” out of the Stealthbox.
Make sure that the socket cup end is exposed.
Place the Stealthbox into position and press down
firmly.
STEP 5: With the Stealthbox removed and wax
square still in position, use a 1/2” drill bit to drill out
the marked location.
After hole is drilled, remove the wax square.
square still in position, use a 1/2” drill bit to drill out
the marked location.
After hole is drilled, remove the wax square.
STEP 6: Place and line up the hole, of one of the
supplied black metal plates to the 1/2” drilled hole
from STEP 5.
Use tape to temporary secure the metal plate into
position.
supplied black metal plates to the 1/2” drilled hole
from STEP 5.
Use tape to temporary secure the metal plate into
position.
START
HERE
Continued on Next Page ➔
w w w. j l a u d i o . c o m
STEP
2.5”
3.5”
A
B