Qsc PLD4.2 Owner's Manual
5
TD-000351-00-D
EN
Amplifi er Control
— Figure 10 —
OUTPUT
HOME
MASTER
CONTROL
CONTROL
-10
-20
LIM
SEL
MUTE
A
1
SEL
MUTE
B
2
SEL
MUTE
C
3
SEL
MUTE
D
4
CLIP
SIG
INPUT
ENTER
EXIT
GAIN
(power
button)
Off Mode
• Rear
power switch is off, the amplifi er is not
operable. The power switch is the AC Mains
disconnect.
disconnect.
• The power button is not illuminated.
• Turn
• Turn
the
power switch to on. The amplifi er enters the mode it was in
when power was removed. The power button is illuminated based on
the mode.
the mode.
Run Mode
• From Standby or Mute All modes, press and release the
power button on the front panel.
• The power button is illuminated blue.
• The amplifi er is fully operable; audio can pass.
• The amplifi er is fully operable; audio can pass.
Standby Mode
• From Mute All or Run modes, press and hold the power
button on the front panel for two to three seconds.
• The power button illuminates solid red.
• The front panel LCD is off.
• The amplifi er is not operable; audio will not pass.
• The front panel LCD is off.
• The amplifi er is not operable; audio will not pass.
Mute All Mode
• From the Run Mode, quickly press and release the power
button.
• The power button fl ashes red.
• The outputs are muted and amplifi ers are off.
• The front panel and DSP functionality are fully operable. Any changes
• The outputs are muted and amplifi ers are off.
• The front panel and DSP functionality are fully operable. Any changes
you make are saved and take effect in the Run Mode.
MASTER CONTROL Knob
• Scrolls up/down and right/left to select menu items and
parameters
• Adjusts
parameters
ENTER Button
• Navigates into the menu structure
• Enters the edit mode for adjusting parameters
• Confi rms the changes you make
• Enters the edit mode for adjusting parameters
• Confi rms the changes you make
EXIT Button
• Navigates out of the menu structure and parameter selection.
• In the edit mode, pressing EXIT reverts the value back to its prior
• In the edit mode, pressing EXIT reverts the value back to its prior
state, and exits the edit mode.
HOME Button
• If you are on the Home screen, pressing HOME displays the
alternate Home screen. Pressing HOME again returns you to the
primary Home screen.
primary Home screen.
• If you are on a navigation screen, pressing HOME takes you Home.
• If you are on an edit screen, pressing HOME will confi rm any value
• If you are on an edit screen, pressing HOME will confi rm any value
being edited and take you to the HOME screen.
GAIN Button
• Pressing the GAIN button from any screen takes you to the
output gain screen for the most recently accessed output channel.
• Pressing GAIN again confi rms the gain change and returns to the
screen you were on when you pressed GAIN.
SEL Buttons
• Use these buttons to navigate between input channels or
output channels. For example, if you are adjusting output gain on
channel A, pressing the channel B SEL button takes you to the gain
adjustment for channel B.
channel A, pressing the channel B SEL button takes you to the gain
adjustment for channel B.
• These buttons change both INPUT and OUTPUT selection at the same
time. For example, if you select OUTPUT A then switch to an Input
screen, you are on Input 1.
screen, you are on Input 1.
• The SEL buttons are active on any Input or Output screen as indicated
by an illuminated SEL button, and a label in the upper right corner of
the screen (Input 1-4 or Output 1-4).
the screen (Input 1-4 or Output 1-4).
• The SEL buttons illuminate blue for output channels, and amber for
input channels.
MUTE Buttons
• Use these buttons to mute the audio of the associated
output channel.
• When the output confi guration is changed, the MUTE buttons are
engaged automatically. You must manually unmute the channels.
LIM LEDs
• Illuminates red when the Limiter is engaged.
-10 and -20 LEDs
• Indicates the dB below maximum output level of the channel.
CLIP LEDs
• Illuminates red when the input signal is being clipped.
SIG LEDs
• Illuminates blue when a signal greater than -40 dB is present.
ENTER
EXIT
HOME
GAIN
GAIN
SEL
SEL
MUTE
LIM
-10 & -20
CLIP
SIG