Q-Logic Q-Forms Kick Panel Enclosures Owner's Manual
Ford Mustang 1994-1996
Remove Original Kick Panel
• Remove threshold plate by carefully prying up on carpet side edge.
• Pull kick panel away from bulkhead to release Christmas tree fastener at rear of panel.
• Tilt bottom front edge upward, slide panel down and away from bulkhead, clearing hood latch release knob.
• Pull kick panel away from bulkhead to release Christmas tree fastener at rear of panel.
• Tilt bottom front edge upward, slide panel down and away from bulkhead, clearing hood latch release knob.
NOTE: Always check the fit of the Q-Forms into the vehicle before any cutting or modifications are done.
Install Speakers
• Cut the speaker holes into the Q-Forms before installing them into the vehicle.
• Install the speakers into the Q-Forms after they have been installed into the vehicle.
• Install speaker wiring and crossover network as per manufacturer’s instructions.
• Using a hole saw of correct size, position pilot drill on dimple at center of speaker mounting surface.
A die grinder or keyhole saw may also be used.
• Lay the supplied polyfill in and around the Q-forms cavity behind the speakers.
• Cut speaker mounting holes taking care as saw exits rear of panel.
• Secure speakers into locations by driving screws through speaker bezel and into mounting surface. Be careful to
center speakers in mounting surface to allow clearance for grill shell.
• Install tweeters as per manufacturer’s instructions.
• Install the speakers into the Q-Forms after they have been installed into the vehicle.
• Install speaker wiring and crossover network as per manufacturer’s instructions.
• Using a hole saw of correct size, position pilot drill on dimple at center of speaker mounting surface.
A die grinder or keyhole saw may also be used.
• Lay the supplied polyfill in and around the Q-forms cavity behind the speakers.
• Cut speaker mounting holes taking care as saw exits rear of panel.
• Secure speakers into locations by driving screws through speaker bezel and into mounting surface. Be careful to
center speakers in mounting surface to allow clearance for grill shell.
• Install tweeters as per manufacturer’s instructions.
Install New Q-Forms Kick Panels (Always predrill all mounting screw locations)
• Lay Q-forms kick panel in approximate location and connect speaker wiring.
• With panel in position, mark location of mounting screws through panel onto bulkhead behind. It will be necessary to
• With panel in position, mark location of mounting screws through panel onto bulkhead behind. It will be necessary to
use a long sharp object to mark upper rear mounting hole location as bulkhead will be about three inches behind
panel.
panel.
• Move panel out of position enough to allow room for drilling mounting holes using 3/16" drill bit.
• Install rubber welt to exposed metal edge extending from bottom of windshield molding to front edge of threshold
• Install rubber welt to exposed metal edge extending from bottom of windshield molding to front edge of threshold
plate.
• Reposition panel into final position and secure using screws provided. Drive 2-1/2" screw through hole at upper front
of panel, through 2 inch spacer, and into bulkhead at hole previously drilled. Drive 3-1/2" screw through hole at upper
rear of panel, through 3" spacer, and into bulkhead at hole
rear of panel, through 3" spacer, and into bulkhead at hole
previously drilled.
• Reinstall threshold plate by carefully aligning clips and pushing firmly
• Reinstall threshold plate by carefully aligning clips and pushing firmly
into place.
• Install grill shells by pressing snugly into woofer cavity.
QL-K2003 Included Hardware:
(2) 1" Screws
(4) 3" Screws
(4) 2 1/2" Spacers (plastic)
(2) 12" rubber welt sectons
(2) 6" x 8" polyfill pieces
(2) 6.25" Q-grills
(4) 3" Screws
(4) 2 1/2" Spacers (plastic)
(2) 12" rubber welt sectons
(2) 6" x 8" polyfill pieces
(2) 6.25" Q-grills
Estimated Installation Time: 1.5 Hrs.
QL-K2003
inst ver 36.1