Q-Logic Q-Forms Kick Panel Enclosures Owner's Manual
QL-K3004
Chrysler Sebring (non-conv.) 1995-1997
Dodge Avenger 1995-1997
Eagle Talon 1995-1997
Mitsubishi Eclipse 1995-1997
Dodge Avenger 1995-1997
Eagle Talon 1995-1997
Mitsubishi Eclipse 1995-1997
Remove Original Kickpanels
• Remove the factory plastic nut from the rear of the panels.
• Remove the factory screw from the upper front edge of the panels.
• Pull out, towards the center of the vehicle, factory panels to release the retaining clips.
• Remove the kickpanels from the vehicle leave the threshold trim pieces fastened into the vehicle.
• Remove the factory screw from the upper front edge of the panels.
• Pull out, towards the center of the vehicle, factory panels to release the retaining clips.
• Remove the kickpanels from the vehicle leave the threshold trim pieces fastened into the vehicle.
NOTE: Always check the fit of the Q-Forms into the vehicle before any cutting or modifications are done.
Install Speakers
• Cut the speaker holes into the Q-Forms before installing them into the vehicle.
• Install the speakers into the Q-Forms after they have been installed into the vehicle.
• Install speaker wiring and crossover network as per manufacturer’s instructions.
• Using a hole saw of correct size, position pilot drill on dimple at center of speaker mounting surface.
A die grinder or keyhole saw may also be used.
• Lay the supplied polyfill in and around the Q-forms cavity behind the speakers.
• Cut speaker mounting holes taking care as saw exits rear of panel.
• Secure speakers into locations by driving screws through speaker bezel and into mounting surface. Be careful to center
speakers in mounting surface to allow clearance for grill shell.
• Install tweeters as per manufacturer’s instructions.
• Install the speakers into the Q-Forms after they have been installed into the vehicle.
• Install speaker wiring and crossover network as per manufacturer’s instructions.
• Using a hole saw of correct size, position pilot drill on dimple at center of speaker mounting surface.
A die grinder or keyhole saw may also be used.
• Lay the supplied polyfill in and around the Q-forms cavity behind the speakers.
• Cut speaker mounting holes taking care as saw exits rear of panel.
• Secure speakers into locations by driving screws through speaker bezel and into mounting surface. Be careful to center
speakers in mounting surface to allow clearance for grill shell.
• Install tweeters as per manufacturer’s instructions.
Install New Q-Forms Kickpanels
DRIVER'S SIDE:
• Slide the Q-Forms into place under the factory threshold trim piece.
(The Q-Form will wrap around the factory dead pedal)
• While Securely holding the Q-Form in place, replace the factory screw through the threshold plate / Q-Form at the
upper front edge.
• While securely holding the Q-Form in place secure the rear edge of the Q-Form through the mounting holes and into the
factory dead pedal with the 2 - 1" screws provided.
• Install the speakers and Q-grill.
PASSENGER'S SIDE:
• Snap the factory plastic nut into the 7/16" hole located at the rear of the Q-Form panel.
• Slide the Q-Forms into place under the factory threshold trim piece.
• While Securely holding the Q-Form in place, replace the factory screw through the threshold plate / Q-Form at the
upper front edge.
• While securely holding the Q-Form in place secure the rear of the panel by pushing the factory plastic nut back onto its
threaded post.
• Install the speakers and Q-grill.
• Slide the Q-Forms into place under the factory threshold trim piece.
(The Q-Form will wrap around the factory dead pedal)
• While Securely holding the Q-Form in place, replace the factory screw through the threshold plate / Q-Form at the
upper front edge.
• While securely holding the Q-Form in place secure the rear edge of the Q-Form through the mounting holes and into the
factory dead pedal with the 2 - 1" screws provided.
• Install the speakers and Q-grill.
PASSENGER'S SIDE:
• Snap the factory plastic nut into the 7/16" hole located at the rear of the Q-Form panel.
• Slide the Q-Forms into place under the factory threshold trim piece.
• While Securely holding the Q-Form in place, replace the factory screw through the threshold plate / Q-Form at the
upper front edge.
• While securely holding the Q-Form in place secure the rear of the panel by pushing the factory plastic nut back onto its
threaded post.
• Install the speakers and Q-grill.
QL-K3004 Included Hardware:
(2) 1" screws
(2) 6" x 8" polyfill pieces
(2) 6.25" Q-grills
(2) 6" x 8" polyfill pieces
(2) 6.25" Q-grills
Estimated Installation Time: 1.5 hrs.
inst ver 61.0