Q-Logic Q-Forms Kick Panel Enclosures Owner's Manual
QL-K1007
Chevrolet / GMC Pickup 1995-1998
Suburban/Yukon/Tahoe 1995-1999
Remove Original Kick Panel
• Remove threshold plate by removing attachment screws.
• Pull kick panel away from bulkhead to release mounting clips.
• Tilt bottom front edge upward and pull kick panel out of vehicle.
• Pull kick panel away from bulkhead to release mounting clips.
• Tilt bottom front edge upward and pull kick panel out of vehicle.
Modify Parking Brake Pedal
• Using two crescent wrenches, carefully bend brake pedal arm so that pedal pad is relocated approximately
1.5 inches to the right.
1.5 inches to the right.
NOTE: Always check the fit of the Q-forms into the vehicle before any cutting or modifications are done.
Preparing the Q-Forms for Speaker Installation
• Cut the speaker holes into the Q-Forms before installing them into the vehicle.
• Install the speakers into the Q-Forms after they have been installed into the vehicle.
• Install speaker wiring and crossover network as per manufacturer’s instructions.
• Using a hole saw of correct size, position pilot drill on dimple at center of speaker mounting surface. A die
grinder or keyhole saw may also be used.
• Lay the supplied polyfill in and around the Q-forms cavity behind the speakers.
• Cut speaker mounting holes taking care as saw exits rear of panel.
• Secure speakers into locations by driving screws through speaker bezel and into
mounting surface. Be careful to center speakers in mounting surface to allow clearance
for grill shell.
• Install tweeters as per manufacturer’s instructions.
• Install the speakers into the Q-Forms after they have been installed into the vehicle.
• Install speaker wiring and crossover network as per manufacturer’s instructions.
• Using a hole saw of correct size, position pilot drill on dimple at center of speaker mounting surface. A die
grinder or keyhole saw may also be used.
• Lay the supplied polyfill in and around the Q-forms cavity behind the speakers.
• Cut speaker mounting holes taking care as saw exits rear of panel.
• Secure speakers into locations by driving screws through speaker bezel and into
mounting surface. Be careful to center speakers in mounting surface to allow clearance
for grill shell.
• Install tweeters as per manufacturer’s instructions.
Install New Q-Forms Kick Panels (Always predrill all mounting screw locations)
• Lay Q-forms kick panel in approximate location and connect speaker wiring.
• Install panel into permanent position previously held by original kick
panel. Be sure front edge of panel fits tightly against rubber door seal.
• Reinstall threshold plate using original screws. It may be helpful to hold
panel tightly against rubber door seal while tightening front screw.
• Install 1/2" mounting screw at upper front corner of panel. (This screw
• Install panel into permanent position previously held by original kick
panel. Be sure front edge of panel fits tightly against rubber door seal.
• Reinstall threshold plate using original screws. It may be helpful to hold
panel tightly against rubber door seal while tightening front screw.
• Install 1/2" mounting screw at upper front corner of panel. (This screw
will attach new Q-Forms panel to the plastic A-pillar molding.)
• Install 1" long screw and 1/2" spacer through hole at rear of panel and
drive into inner bulkhead sheetmetal. It may be helpful to predrill screw
pilot hole if installed without power tools.
pilot hole if installed without power tools.
• Once installation is complete, try hood latch release to be sure it
activates smoothly.
• Install grill shells by pressing snugly into woofer cavity.
5/18/00
QL-K1007 Included Hardware:
(2) 3/4" screws
(2) 1" screws
(2) 1/2" plastic spacers
(2) 6" x 8" polyfill pieces
(2) 6.25" Q-grills
(2) 1" screws
(2) 1/2" plastic spacers
(2) 6" x 8" polyfill pieces
(2) 6.25" Q-grills
Estimated InstallationTime: 1.5 Hrs.