CHY FIREMATE CO. LTD. BT003 User Manual
compliance requirements, the antenna used for this transmitter must be
installed to provide a separation distance of at least 20cm from all persons and
must not be colocated or operating in conjunction with any other antenna or
transmitter.” This device complies with part 15 of the FCC rules. Operation
is subject to the following two conditions (1) This device may not cause
harmful interference and (2) This device must accept any interference
received, including interference that may cause undesired operation.
IMPORTANT NOTE: In the event that these conditions can not be met (for
example certain laptop configurations or colocation with another transmitter),
then the FCC authorization is no longer considered valid and the FCC ID can
not be used on the final product. In these circumstances, the OEM integrator
will be responsible for reevaluating the end product (including the transmitter)
and obtaining a separate FCC authorization. This device is intended only for
OEM integrators under the following conditions: The antenna must be installed
such that 20 cm is maintained between the antenna and users. As long as a
condition above is met, further transmitter test will not be required. However,
the OEM integrator is still responsible for testing their end product for any
additional compliance requirements required with this module installed (for
example, digital device emissions, PC peripheral requirements, etc.).
Industry Canada Statement
This device complies with Industry Canada licence‐exempt RSS standard.
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference
that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
installed to provide a separation distance of at least 20cm from all persons and
must not be colocated or operating in conjunction with any other antenna or
transmitter.” This device complies with part 15 of the FCC rules. Operation
is subject to the following two conditions (1) This device may not cause
harmful interference and (2) This device must accept any interference
received, including interference that may cause undesired operation.
IMPORTANT NOTE: In the event that these conditions can not be met (for
example certain laptop configurations or colocation with another transmitter),
then the FCC authorization is no longer considered valid and the FCC ID can
not be used on the final product. In these circumstances, the OEM integrator
will be responsible for reevaluating the end product (including the transmitter)
and obtaining a separate FCC authorization. This device is intended only for
OEM integrators under the following conditions: The antenna must be installed
such that 20 cm is maintained between the antenna and users. As long as a
condition above is met, further transmitter test will not be required. However,
the OEM integrator is still responsible for testing their end product for any
additional compliance requirements required with this module installed (for
example, digital device emissions, PC peripheral requirements, etc.).
Industry Canada Statement
This device complies with Industry Canada licence‐exempt RSS standard.
Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference
that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions
suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de
l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de
l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
The host device shall be properly labelled to identify the modules within the host
device.
device.
The Industry Canada certification label of a module shall be clearly visible at all
times when installed in the host device, otherwise the host device must be labelled
to display the Industry Canada certification number of the module, preceded by the
words “Contains transmitter module”, or the word “Contains”, or similar
to display the Industry Canada certification number of the module, preceded by the
words “Contains transmitter module”, or the word “Contains”, or similar
wording expressing the same meaning, as follows:
“Contains transmitter module IC: 22512‐BT003
“Contains transmitter module IC: 22512‐BT003