Thunder Tiger Corp. TT-FHM2P4G-A14 User Manual

1.   Transmitter Antenna: Straighten up the antenna before operating the model.
2.   Power Indicator: The LED light indicates power is "on" or "off". 
3.   Edit Buttons: The left and right buttons are the "functions" selecting keys. The up(+) and down(-) buttons are the value 

adjusting keys.  For additional details on specific operation, please refer to the "function" setting procedure (Page 8).

4.   LCD Display: The Cougar transmitter features an "Easy-to-Read” screen. Use the "Edit Buttons" to select the function 

(left and right key) and change settings (with the "up" & "down" keys). For additional details on specific operation, 

please refer to the "Function" setting procedure (Page 8). 

5.   Digital Steering Trim lever: Push this lever left or right to adjust the center point of the steering servo. The cursor will 

move on the top ruler line of the LCD screen to display the current position. 

6.   Digital Throttle Trim lever: Push this lever up or down to adjust the center point of the throttle/brake servo. The cursor 

will move on the left ruler line of the LCD screen to display the current position. This adjustment sets the braking 

amount of "Drag Brake" and "Coast Brake".

NOTE: The Digital Throttle Trim function adjusts neutral point without affecting maximum throttle servo travel and 

full-throttle position.
The Digital Steering Trim function adjusts maximum steering servo travel for both left and right steering. If adjustments 

are incorrect, steering linkage binding or damages to the steering servo may occur. 

7.   Digital Steering D/R(Dual Rate) lever: Push this lever left or right to adjust the amount of the steering dual rate. Right 

to increase dual rate amount and left to decrease the amount.

8.   AUX Ch Button: Provides an extra function for the control of the model.
9.   External Charging Jack: For rechargeable NiCd/NiHM battery pack on the transmitter only. 
10. 24GHz binding SW: The Binding SW button is located on the back of the 2.4GHz transmitter unit. For additional 

details, please refer to the "Binding" setting procedure (Page 7).

11. Steering Wheel: Controls the steering of the model.
12. Power Switch: Slide to turn the transmitter on or off.
13. Throttle Trigger: Pull or push to control throttle on the model.
14. Steering Tension Adjustment: Use a Phillip type screw driver to tighten or loosen the tension on the steering wheel.
15. Battery Cover: Slide for removing the cover and install / remove the batteries.

1.   Transmitter Antenna: Straighten up the antenna before operating the model.
2.   Battery Level Indicator: Three LEDs indicate the battery voltage level. If the Red LED flashes, please replace the 

batteries.

3.   HI/LO Throttle ATV (Adjustable Travel Volume): Provide the function to let you independently preset the maximum 

travel of the throttle servo either side (high / low) of neutral.

4.   Servo reversing switches: To reverse the servo's rotation direction at the flip of the switch. The reversing switches 

are recessed into the transmitter to prevent accidental operation.

iFHss/iFHss

+

 switch:iFHss

+

 provides faster and more reliable data transmission, and has less power consumption. 

Note you should use TRS402ss receiver in compliance with iFHss

+

 mode.

5.   Steering Trim: Adjusts the steering in small increments or decrements to run the model straight.
6.   Throttle Trim: Adjusts the throttle in small increments or decrements to shift the neutral position.
7.   Steering D/R (Dual Rates): Push this lever left or right to adjust the amount of the steering dual rate. Right to 

increase dual rate amount and left to decrease the amount.

8.   AUX Ch Button: Provides an extra function for the control of the model. (for Cougar P3 only)
9.   External Charging Jack: For rechargeable NiCd/NiHM battery pack on the transmitter only. 
10.  2.4GHz binding SW: The Binding SW button is located on the back of the 2.4GHz transmitter. For additional details, 

please refer to the “Binding” setting procedure (Page 7).

11. Steering Wheel: Control the steering of the model.
12. Power Switch: Slide to turn the transmitter on or off.
13. Throttle Trigger: Pull or push to control the movement of the model.
14. Steering Tension Adjustment: Use a Phillip type screwdriver to tighten or loosen the tension of the steering wheel. 
15. Battery Cover: Slide cover to install or remove batteries.