Inclusion Solutions LLC 315BBRTX User Manual
www.InclusionSolutions.com
1-800-971-8281
Thank you for purchasing the BigBell - your
first step in becoming accessible to people
with disabilities. This alert system is
designed to meet the standards set forth by
the United States Government in the
Americans With Disabilities Act. It is
essential that the BigBell be properly
installed and maintained consistent with the
requirements of the law.
ENCLOSED YOU WILL FIND:
• BigBell™ Pushbutton
• Chime Receiver
• Sticker Set
• Four screws and wall anchors
• Glass Adhesive with double sided tape
TOOLS NEEDED:
• Small Phillips head screwdriver
• Drill with 7/32” Drill Bit
• Marking Pen
• Tape Measure
MOUNTING LOCATION
(REQUIRED BY THE ADA)
• Outside the front door of the establishment
on the latch side of the door.
• Mount the BigBell at street level.
• The BigBell must be mounted in a location
where it will be unobstructed by any barriers.
A person should be able to approach within
3” of the Pushbutton without encountering
protruding objects or standing within the
swing of the door.
MOUNTING HEIGHT (REQUIRED BY ADA)
Your BigBell must be mounted between 32”
and 48” from the ground so that it is
accessible
for
customers
who
use
wheelchairs.
The ideal height, as set forth by law is 36”
The ideal height, as set forth by law is 36”
MOUNTING INSTRUCTIONS
1. Carefully separate top from the back plate.
2. Remove the three screws from inside the
Pushbutton and retain for final assembly.
3. Position the back plate on the wall in the
desired location and mark or scribe the
center of the four mounting holes onto wall
4. Drill 7/32” holes into the wall at the four
marked locations
5. Insert the plastic wall anchors into drilled
holes
5. Screw the back plate onto the wall.
6. Remove plastic strip in the battery casing
to power unit.
7. Change melody to desired tone (see
Changing Tone/Melody Selection)
7. Position the top enclosure on the back
plate and reinstall the three screws
ALTERNATIVE MOUNTING METHOD
The BigBell Pushbutton can also be
mounted to glass or other smooth surfaces
with the enclosed double-sided tape and
adhesive. Use the adhesive to adhere the
Pushbutton to the glass or other surface
utilizing the double sided tape as a
temporary hold while the glue hardens.
BIGBELL BATTERY INSTALLATION
1. For Battery Operation: Remove the
battery cover on the back of the receiver.
Insert 4 AA batteries in the correct
orientation.
2. For AC Power Operation: Plug the wall
transformer into a 120 VAC outlet. Plug the
power cord into the bottom of the receiver.
AC operation is preferred.
TEST
Once the BigBell has been mounted the
system should be tested to ensure it is
working properly.
1. Plug the Basic receiver into the desired
outlet.
2. Press the BigBell: The red LED light
should activate on the pushbutton and
the receiver should chime.
the receiver should chime.
CHANGING TONE/MELODY SELECTION
If you would like a different tone or melody to
play when the BigBell is pushed there are a
number of unique options.
1. Remove the top section of the
Pushbutton by removing the three
screws.
screws.
2. Locate the small grey button to the upper
right of the battery casing. The button is
framed with a piece of silver.
framed with a piece of silver.
3. To change tone or melody, press the
grey button once. The receiver will play
the next selection.
the next selection.
4. Continue to press the button to change
the melody.
Note: If you change songs or tones too
rapidly, the Receiver will not play each
selection. Only the last melody or tone
selected will play. Selecting while Receiver is
playing will switch system to new setting, but
Receiver will only finish playing tone or
melody already in progress.
FRONT/BACK DOOR CHIME OPERATION
If you have multiple BigBells and wish to
differentiate the front and back doors, scroll
and set a different selection for each
Pushbutton at each door. The tone/melody
that is played allows you to determine which
button was pressed.
VOLUME CONTROL
Adjust loudness by moving the volume
switch on the Receiver.
STROBE LIGHT – To activate the strobe
light function, make sure the Strobe switch is
turned to ON
BATTERY INSTALLATION --
PUSHBUTTON
1. To Replace Batteries, open cover of
If you have multiple BigBells and wish to
differentiate the front and back doors, scroll
and set a different selection for each
Pushbutton at each door. The tone/melody
that is played allows you to determine which
button was pressed.
VOLUME CONTROL
Adjust loudness by moving the volume
switch on the Receiver.
STROBE LIGHT – To activate the strobe
light function, make sure the Strobe switch is
turned to ON
BATTERY INSTALLATION --
PUSHBUTTON
1. To Replace Batteries, open cover of
BigBell and carefully remove batteries (if
they will not come out, narrow pliers or a
screwdriver will help remove them)
they will not come out, narrow pliers or a
screwdriver will help remove them)
2. Dispose of used batteries properly.
3. Replace with UL approved Type CR2032
3. Replace with UL approved Type CR2032
batteries.
CAUTION
-
The batteries used in this device
may present a risk of fire or chemical burn if
mistreated. Do not recharge, disassemble,
heat above 100 degrees Celsius (212
Fahrenheit), or incinerate. Replace with UL
approved Type CR2032 3 volt only. Use of
another battery may present a risk of fire or
explosion.
mistreated. Do not recharge, disassemble,
heat above 100 degrees Celsius (212
Fahrenheit), or incinerate. Replace with UL
approved Type CR2032 3 volt only. Use of
another battery may present a risk of fire or
explosion.
TROUBLESHOOTING TIPS
PROBLEM: Receiver does not sound when
Pushbutton is pressed.
SUGGESTION:
Pushbutton is pressed.
SUGGESTION:
Verify
that
Pushbutton
batteries are installed correctly and battery
contacts are in the correct position. Try
replacing batteries on chime and/or receiver.
Be sure frequency is the same on Button
and Receiver (see privacy code section).
Ensure that the receiver is mounted away
from all objects that may cause interference.
These items include: motors/engines, neon
lights, dimmers, fans, and computers.
PROBLEM: Chime only plays one melody
SUGGESTION: Press Scroll Button on
inside of Pushbutton to change sound
options.
PROBLEM: Receiver sometimes plays
without anyone pressing Pushbutton.
SUGGESTION: If another BigBell is on the
same frequency nearby, it could accidentally
trigger your system. If this happens, change
privacy code (see below).
TO CHANGE PRIVACY CODES
It is not necessary to change the privacy
code unless interference occurs (ghost rings,
intermittent signal, etc). If, for example,
several businesses near yours have also
purchased a BigBell, you may encounter
interference. If you need to change the code:
contacts are in the correct position. Try
replacing batteries on chime and/or receiver.
Be sure frequency is the same on Button
and Receiver (see privacy code section).
Ensure that the receiver is mounted away
from all objects that may cause interference.
These items include: motors/engines, neon
lights, dimmers, fans, and computers.
PROBLEM: Chime only plays one melody
SUGGESTION: Press Scroll Button on
inside of Pushbutton to change sound
options.
PROBLEM: Receiver sometimes plays
without anyone pressing Pushbutton.
SUGGESTION: If another BigBell is on the
same frequency nearby, it could accidentally
trigger your system. If this happens, change
privacy code (see below).
TO CHANGE PRIVACY CODES
It is not necessary to change the privacy
code unless interference occurs (ghost rings,
intermittent signal, etc). If, for example,
several businesses near yours have also
purchased a BigBell, you may encounter
interference. If you need to change the code:
1. Remove batteries from Receiver
2. Use a pen to change the DIP switch
2. Use a pen to change the DIP switch
settings to a different code.
3. Locate the DIP switch on the Pushbutton.
Using a pen, change the DIP settings to the
same as on the receiver.
Note: It doesn’t matter which switches are
set, but be sure that the receiver and
transmitter switches match. If the switches
do not match, the ADA BigBell will not work.
IMPORTANT: EVERY TIME A SWITCH IS
SET
Using a pen, change the DIP settings to the
same as on the receiver.
Note: It doesn’t matter which switches are
set, but be sure that the receiver and
transmitter switches match. If the switches
do not match, the ADA BigBell will not work.
IMPORTANT: EVERY TIME A SWITCH IS
SET
ON
THE
RECEIVER,
THE
CORRESPONDING SWITCH MUST BE
SET ON THE PUSHBUTTON.
Suggestion: Begin by setting just one
switch on the Receiver and the same switch
on the Pushbutton. Test to see if the problem
is eliminated. If the system is still not working
properly, try setting another switch.
MAXIMIZNG OPERATING RANGE
The BigBell has an operating range of up to
1000 feet under ideal circumstances –
normal operation is in excess of 300 feet.
However, certain materials, such as
transmission through concrete or heavy
walls may diminish the signal and lessen
operating range, just as with a cell phone.
• In order to maximize range, the receiver
SET ON THE PUSHBUTTON.
Suggestion: Begin by setting just one
switch on the Receiver and the same switch
on the Pushbutton. Test to see if the problem
is eliminated. If the system is still not working
properly, try setting another switch.
MAXIMIZNG OPERATING RANGE
The BigBell has an operating range of up to
1000 feet under ideal circumstances –
normal operation is in excess of 300 feet.
However, certain materials, such as
transmission through concrete or heavy
walls may diminish the signal and lessen
operating range, just as with a cell phone.
• In order to maximize range, the receiver
should be placed or hung on a wall at
approximately 6-7 feet in the air, with the
unit facing in the direction of the
Pushbutton
approximately 6-7 feet in the air, with the
unit facing in the direction of the
Pushbutton
• You may also wish to move the receiver
to a location in proximity to the
Pushbutton but as close to the accessible
entrance door (and installed BigBell unit)
as possible.
Pushbutton but as close to the accessible
entrance door (and installed BigBell unit)
as possible.
• You may also want to experiment with
different locations for the Pushbutton to
improve range.
improve range.
• If possible, do not place the Pushbutton
on a metal surface, as this will also
diminish range.
diminish range.
LIMITED WARRANTY
The product you have purchased is guaranteed
against defects in workmanship and materials for one
year from date of purchase. If the product fails due to
a manufacturing defect during normal use, return the
product to the store where purchased for a
replacement
OR send product to:
Inclusion Solutions Customer Service
6909 N. Western Ave
Chicago, IL 60645
Not Covered - Batteries and other expendable items,
repair service, adjustment and calibration due to
misuse, abuse or negligence nor lost, damaged, or
stolen BigBells are covered by this warranty.
Unauthorized service or modification of the product or
of any furnished components will void this warranty in
its entirety. This warranty does not include
reimbursement for inconvenience, installation, set-up
time, loss of use, postage, unauthorized service, or
other products used in conjunction with, but are not
supplied by, Inclusion Solutions.
All requests for replacement must include a dated
sales receipt or Inclusion Solutions invoice (copies
accepted) and this guarantee statement. INCLUSION
SOLUTIONS SHALL NOT BE LIABLE FOR LOST
PROFITS, INDIRECT, SPECIAL, EXEMPLARY,
INCIDENTAL OR CONSEQUENTIAL DAMAGES
INCLUDING WITHOUT LIMITATION ANY SUCH
DAMAGES DUE TO IMPROPER WIRING OR
MISUSE OF THE PRODUCT. INCLUSION
SOLUTIONS ALSO SHALL NOT BE RESPONSIBLE
FOR ANY DAMAGES OR CONSEQUENCES OF
LITIGATION BROUGHT UNDER THE AMERICANS
WITH DISABILITIES ACT OR OTHER CIVIL RIGHTS
LITIGATION.
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, &
2. This device must accept any interference received,
including interference that may cause undesired
operation. This device complies with RSS-210 of
Industry Canada.
If you have any questions or need further assistance,
please call Inclusion Solutions toll free at 1-866-232-
5487 or visit us at
The product you have purchased is guaranteed
against defects in workmanship and materials for one
year from date of purchase. If the product fails due to
a manufacturing defect during normal use, return the
product to the store where purchased for a
replacement
OR send product to:
Inclusion Solutions Customer Service
6909 N. Western Ave
Chicago, IL 60645
Not Covered - Batteries and other expendable items,
repair service, adjustment and calibration due to
misuse, abuse or negligence nor lost, damaged, or
stolen BigBells are covered by this warranty.
Unauthorized service or modification of the product or
of any furnished components will void this warranty in
its entirety. This warranty does not include
reimbursement for inconvenience, installation, set-up
time, loss of use, postage, unauthorized service, or
other products used in conjunction with, but are not
supplied by, Inclusion Solutions.
All requests for replacement must include a dated
sales receipt or Inclusion Solutions invoice (copies
accepted) and this guarantee statement. INCLUSION
SOLUTIONS SHALL NOT BE LIABLE FOR LOST
PROFITS, INDIRECT, SPECIAL, EXEMPLARY,
INCIDENTAL OR CONSEQUENTIAL DAMAGES
INCLUDING WITHOUT LIMITATION ANY SUCH
DAMAGES DUE TO IMPROPER WIRING OR
MISUSE OF THE PRODUCT. INCLUSION
SOLUTIONS ALSO SHALL NOT BE RESPONSIBLE
FOR ANY DAMAGES OR CONSEQUENCES OF
LITIGATION BROUGHT UNDER THE AMERICANS
WITH DISABILITIES ACT OR OTHER CIVIL RIGHTS
LITIGATION.
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference, &
2. This device must accept any interference received,
including interference that may cause undesired
operation. This device complies with RSS-210 of
Industry Canada.
If you have any questions or need further assistance,
please call Inclusion Solutions toll free at 1-866-232-
5487 or visit us at
www.inclusionsolutions.com