Cypress Semiconductor 3025 User Manual

EZ-BLE™ WICED Module

•

198 Champion Court

•

San Jose

,

CA 95134-1709

•

408-943-2600

Document Number: 002-xxxxx Rev. ** 

 Revised April 10, 2017

The  CYBLE-0130XX-00  is  a  fully  integrated  Bluetooth



  Low

Energy (BLE) wireless module solution. The CYBLE-0130XX-00

includes  onboard  crystal  oscillator,  passive  components,  flash

memory, and the Cypress CYW20737 silicon device. Refer to the

CYW20737 datasheet for additional details on the capabilities of

the silicon device used in this module. 
The  CYBLE-0130XX-00  supports  a  number  of  peripheral

functions  (ADC  and  PWM),  as  well  as  UART  serial

communication. The CYBLE-0130XX-00 includes a royalty-free

BLE  stack  compatible  with  Bluetooth  4.1  in  a  14.5  ×  19.2  ×

2.25mm package.
The  CYBLE-013025-00  includes  128KB  of  onboard  flash

memory and is designed to allow for self-sufficient opperation.

The  CYBLE-013030-00  does  not  contain  onboard  flash,

providing  maximum  cost  optimization  and  allowing  for  hosted

control or application RAM upload, or interface to external flash

on the host board. 
The  CYBLE-0130XX-00  is  fully  certified  by  Bluetooth  SIG  is

targeted  at  applications  requiring  cost  optimized  BLE  wireless

connectivity.  The  CYBLE-0130XX-00  is  footprint  compatible

[1]

with the CYBLE-x120xx-00 module family. 

n

Module size: 14.52 mm × 19.20 mm × 2.25 mm 

n

Bluetooth LE 4.1 single-mode module

p

QDID: TBD

p

Declaration ID: TBD

n

Certified to FCC, IC, MIC, and CE regulations

n

Castelated solder pad connections for ease-of-use

n

128-KB flash memory, 60-KB SRAM memory

n

Up to 14 GPIOs configurable as open drain high/low, 

pull-up/pull-down, HI-Z analog, HI-Z digital, or strong output

n

Industrial temperature range: –30 °C to +85 °C

n

Cortex-M3 32-bit processor 

n

Watchdog timer with dedicated internal low-speed oscillator

n

Supports A4WP wireless charging

n

Supports fRSA encryption/decryption and key exchange 

mechanisms (up to 4 kbit)

n

Supports NFC tag-based “tap-to-pair”

n

Supports IR learning with built-in IR modulator

n

Maximum TX output power: +4.0 dbm

n

RX Receive Sensitivity: –94 dbm

n

Received signal strength indicator (RSSI) with 1-dB resolution

n

TX current consumption: 9.1 mA 

n

RX current consumption: 9.8 mA 

n

Cypress CYW20737 silicon low power mode support

p

Sleep: 12 uA typical

p

Deep Sleep: TBD 

n

10-bit auxiliary ADC with nine analog channels

n

Serial Communications interface (compatible with Philips

®

 I2C 

slaves)

n

Four dedicated PWM blocks 

n

BLE protocol stack supporting generic access profile (GAP) 

Central, Peripheral, Observer, or Broadcaster roles

n

Programmable output power control

CYBLE-0130XX-00 provides all necessary components required

to operate BLE communication standards. 

n

Proven hardware design ready to use

n

Cost optimized for applications without space constraints

n

Non-volatile memory for complex application development

n

Over-the-air update capable for in-field updates

n

Bluetooth SIG qualified with QDID and Declaration ID 

n

Fully certified module eliminates the time needed for design, 

development and certification processes

n

WICED™ SMART provides an easy-to-use integrated design 

environment (IDE) to configure, develop, and program a BLE 

application

1. CYBLE-0130XX-00 global connections (Power, Ground, XRES, etc) are pad compatible with the CYBLE-x120xx-00 family of modules. Available GPIO and functions 

may not be 100% compatible with your design. A review of the pad location and function within your design should be complete to determine if the CYBLE-0130XX-00 

is completely pad-compatible to the CYBLE-x120xx-00 modules.