Automatic Bar Controls Inc. MS1108 User Manual
Master User Manual
FCC Information.
This equipment has been tested and found to comply with the limits for a class B digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected
• Consult the dealer or an experienced radio/TV technician for help
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
• This device may not cause harmful interference.
• This device must accept any interference received, including interference that may cause
This equipment has been tested and found to comply with the limits for a class B digital device,
pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment to an outlet on a circuit different from that to which the receiver is
connected
• Consult the dealer or an experienced radio/TV technician for help
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
• This device may not cause harmful interference.
• This device must accept any interference received, including interference that may cause
undesired operation
Canada information:
This device complies with Industry Canada licence
This device complies with Industry Canada licence
‐exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de
brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de
brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
How to start:
1, Install the two antennas, make sure they are perpendicular to the ground, otherwise
communication distance will be affected.
communication distance will be affected.
2, Connect the Ethernet cable or RS232 cable for data link. The Ethernet is more quick and steady
than the COM port. The default setting of the Master is: IP address 192.168.1.121, Subnet mask
255.255.255.0, Default gateway 192.168.1.1, user can change this setting through COM port or PC
direct connection. The Master can obtain a IP address automatically with a DHCP protocol.
than the COM port. The default setting of the Master is: IP address 192.168.1.121, Subnet mask
255.255.255.0, Default gateway 192.168.1.1, user can change this setting through COM port or PC
direct connection. The Master can obtain a IP address automatically with a DHCP protocol.
3, Plug in power.
4, Configure the Master.
5, Add devices to the Master, add product to the Master.
6, Configure the devices.
7, Set Master date and time, clean old data.
8, Read pour data, the master supports different protocols: Skylink which is integrated in Skyman API,
Harton, Berg, Web API. Any of them can be used as a data reading protocol, but DO NOT use them
at the same time.
Harton, Berg, Web API. Any of them can be used as a data reading protocol, but DO NOT use them
at the same time.