Moxa NPort 5650I-8-DT NPORT 5650I-8-DT User Manual
Product codes
NPORT 5650I-8-DT
1
w w w. m o x a . c o m
i n f o @ m o x a . c o m
Serial-to-Ethernet Device Servers
Overview
NPort
®
5600 Desktop Series
8-port RS-232/422/485 serial device servers
8 serial ports supporting RS-232/422/485
›
Compact desktop design
›
10/100M auto-sensing Ethernet
›
Built-in 15 KV ESD protection for all serial signals
›
Easy IP address configuration with LCD panel
›
Choice of configuration methods: Web console, Telnet console, and
›
Windows utility
Versatile socket operation modes, including TCP Server, TCP
›
Client, UDP, and Real COM
SNMP MIB-II for network management
›
Built-in speaker: Use your own voice as the alert when exceptions
›
occur
NPort® 5600-8-DT device servers can conveniently and transparently
connect 8 serial devices to an Ethernet network, allowing you to
network your existing serial devices with only basic configuration. You
can both centralize management of your serial devices and distribute
management hosts over the network. Since the NPort® 5600-8-DT
device servers have a smaller form factor compared to our 19-inch
models, they are a great choice for applications that need additional
serial ports, but for which mounting rails are not available.
connect 8 serial devices to an Ethernet network, allowing you to
network your existing serial devices with only basic configuration. You
can both centralize management of your serial devices and distribute
management hosts over the network. Since the NPort® 5600-8-DT
device servers have a smaller form factor compared to our 19-inch
models, they are a great choice for applications that need additional
serial ports, but for which mounting rails are not available.
Convenient Design for RS-485 Applications
The NPort® 5650-8-DT device servers support selectable 1 KΩ and
150 KΩ pull high/low resistors and a 120 Ω terminator. In some
critical environments, termination resistors may be needed to prevent
the reflection of serial signals. When using termination resistors, it
is also important to set the pull high/low resistors correctly so that
the electrical signal is not corrupted. Since no set of resistor values
is universally compatible with all environments, NPort® 5600-8-DT
device servers use DIP switches to allow users to adjust termination
and pull high/low resistor values manually for each serial port.
150 KΩ pull high/low resistors and a 120 Ω terminator. In some
critical environments, termination resistors may be needed to prevent
the reflection of serial signals. When using termination resistors, it
is also important to set the pull high/low resistors correctly so that
the electrical signal is not corrupted. Since no set of resistor values
is universally compatible with all environments, NPort® 5600-8-DT
device servers use DIP switches to allow users to adjust termination
and pull high/low resistor values manually for each serial port.
Convenient Power Inputs
The NPort® 5650-8-DT device servers support both power terminal
blocks and power jacks for ease of use and greater flexibility. Users
can connect the terminal block directly to a DC power source, or use
the power jack to connect to an AC circuit through an adaptor.
blocks and power jacks for ease of use and greater flexibility. Users
can connect the terminal block directly to a DC power source, or use
the power jack to connect to an AC circuit through an adaptor.
LED Indicators to Ease Your Maintenance Tasks
The System LED, Serial Tx/Rx LEDs, and Ethernet LEDs (located on the
RJ45 connector) provide a great tool for basic maintenance tasks and
help engineers analyze problems in the field. The NPort® 5600’s LEDs
not only indicate current system and network status, but also help field
engineers monitor the status of attached serial devices.
RJ45 connector) provide a great tool for basic maintenance tasks and
help engineers analyze problems in the field. The NPort® 5600’s LEDs
not only indicate current system and network status, but also help field
engineers monitor the status of attached serial devices.
Two Ethernet Ports for Convenient Cascade Wiring
The NPort® 5600-8-DT device servers come with two Ethernet ports
that can be used as Ethernet switch ports. Connect one port to the
network or server, and the other port to another Ethernet device. The
dual Ethernet ports eliminate the need to connect each device to a
separate Ethernet switch, reducing wiring costs.
that can be used as Ethernet switch ports. Connect one port to the
network or server, and the other port to another Ethernet device. The
dual Ethernet ports eliminate the need to connect each device to a
separate Ethernet switch, reducing wiring costs.