SABINE INC. DS80P User Manual
BACK PANEL (XLR Connector):
Antenna A Input:
1.
TNC connector for dipole antennas (included), front-to-back antenna cables (included), or antenna cable to
active extension antenna.
Antenna A Output:
Antenna A Output:
2.
Daisy-chain to the input of another receiver-frame to form an antenna network.
Power Cord Input:
3.
(Cord with local plug configuration Included). 100-240 VAC, 50/60Hz, 15 W, 250V 320mA slow-blow fuse
(spare included)
Ethernet:
Ethernet:
4.
Connect to a computer or network. Multiple receiver-frames can be daisy-chained together to form a network.
(Under
construction)
GPIO/RS232:
5.
This connector combines a General Purpose Input / Output (GPIO) and a RS232 on one DB25 connector. The
RS232 can be disabled to add up to 24 GPIO pins.
RS232: The pinout for the RS232 is the standard pinout. Pin 2 on the receiver is transmit, pin 3 is receive, and pin 7 is ground.
Most computers now use a DB9 connector for RS232. The standard off-the-shelf DB9 to DB25 cable will work. This cable swaps
pins 2 and 3 internally. If you computer has a DB25 connector for RS232, use a straight DB25 to DB25 cable. Do not use a null
modem cable.
GPIO: GPIO acts like a contact closure. Use SACOM
RS232: The pinout for the RS232 is the standard pinout. Pin 2 on the receiver is transmit, pin 3 is receive, and pin 7 is ground.
Most computers now use a DB9 connector for RS232. The standard off-the-shelf DB9 to DB25 cable will work. This cable swaps
pins 2 and 3 internally. If you computer has a DB25 connector for RS232, use a straight DB25 to DB25 cable. Do not use a null
modem cable.
GPIO: GPIO acts like a contact closure. Use SACOM
™
Remote to assign an event that toggles the GPIO pin. The factory
default toggles pins X through X to correspond to muting a receiver module. SACOM
™
Remote has a feature that lets you assign
how the system responds to a transmitter mute (see SACOM Remote)
A. Mute the channel’s receiver audio. (Factory default)
B. Toggle the GPIO but do not mute the receiver audio. Use this with automated mixers or echo cancelling DSPs.
C. Mute the channels receiver audio and toggle the GIPO pin.
AES/EBU-3 Digital-Audio Output:
A. Mute the channel’s receiver audio. (Factory default)
B. Toggle the GPIO but do not mute the receiver audio. Use this with automated mixers or echo cancelling DSPs.
C. Mute the channels receiver audio and toggle the GIPO pin.
AES/EBU-3 Digital-Audio Output:
6.
Uses the standard Yamaha wiring convention(1). (NOTE: This feature is optional. The
connector jack is included on all receivers, but the feature must be specified at the time of purchase. It cannot be added at a later
date.)
BNC connectors:
date.)
BNC connectors:
7.
for word clock digital-audio synchronizing.
Audio Output Jacks:
8.
Configured for four or eight-module receiver frames and for XLR or Euro-block terminal connectors.
Antenna B Input:
9.
TNC connector for dipole antennas (included), front-to-back antenna cables (included), or antenna cable to
active extension antenna (see section on antennas, antenna placement and antenna cables).
Antenna B Output:
Antenna B Output:
10.
Daisy-chain to the input of another receiver-frame to form an antenna network.
DC Input:
11.
Optional external DC power source eliminates the need for AC input or, can be used as a redundant, back-up power
source (Available on Euro Block models only).
8
Digital Wireless Microphone Systems
Receiver:
SABINE INC.
l
13301 NW US Highway 441
l
Alachua, Florida 32615-8544 USA
l
Phone: +USA (386) 418-2000
l
Fax: +USA (386) 418-2001
l
www.SacomUSA.com
MIC OUTPUTS
AES
3
50-60 Hz 100-240 VAC
ANTENNA A
ETHERNET
WORD CLOCK
ANTENNA B
RS
232-GPIO
4
G
- +
3
G
- +
2
G
- +
1
G
- +
8
G
- +
7
G
- +
6
G
- +
5
G
- +
Mfgr: Sabine, Inc., Alachua, FL.
DS8800
Made In USA
TM
OUT
IN
IN
OUT
OUT
IN
BACK PANEL (Euro-Block Connector):
MIC OUTPUTS
IN
AES
3
IN
50-60 Hz 100-240 VAC
ANTENNA A
1
2
3
4
ETHERNET
WORD CLOCK
ANTENNA B
RS
232-GPIO
5
6
7
8
Mfgr: Sabine, Inc., Alachua, FL.
DS8800
Made In USA
TM
IN
OUT
OUT
OUT
2
3
4
5
1
6
7
9
11
2
3
4
5
1
6
7
9
8
10
10